Counting matching models…
Holder for Philips Hue Bridge v2 to the SKÅDIS pinwall. Model is very fine and flexible (only 1mm walls). There is no weight to support. I didn't add the locking pins - it's held down by the cabling. Needs supports to print. The supports…
The holder for my BIP&GO has been lost so I made a new one Use PETG with organic supports to print I used an 0.6mm nozzle with 0.3mm
Convert your food dehydrator into a filament dryer by just adding a center holder and some spacers. I designed a center filament roll holder and two spacers with different height. The cover tray needs a less high spacer than the others. I…
The model is slightly skewed as 90° does not really exist in house building. I added a gap so the mains of the sonoff don't need to be loosened during installation. Perfectly level in my house :-) Now I can finally get rid of the HUE…
Gridfinity stackable ER16 Collet Holder - 4x1 PETG, 0.6n 0.3mm, 5% infill no support or brim Zach Freedman's GridFinity System Parametric templates: https://a360.co/3ccHbsg 📥 Divider Bins + Trays: https://bit.ly/3E6vNrR 👁 Window Bins:…
I needed a holder for a Netgear GS110 to fix vertically on the SKÅDIS pegboard. It also fits other Netgear GS1xx series. It uses a dovetail system (see below) removing the hassle of those pegs. It's a tight fit. I added a file with…
Standard Lista boxes in two sizes - single and double height 73.5 x 147 x 25.5 73.5 x 73.5 x 25.5 wall 2.5 Easy to print
Holder for an Aqara Vibrarion sensor to detect opening of the letterbox. Print on left side - no supports needed I used PETG with 0.6n
Quick repair for CPAP air hose that got damaged Supports are already designed into - use “Enforcers only” As can be seen in picture the support snaps off easily. Be sure to remove all artifacts - you don't want to inhale them !
Adaption of 17mm ball mount to use M4x30 skrew
Adapter to charge LiPo batteries with a Skyrc MC3000 (or any other) charger Made for LiPo with JST 2.0 adapters I used the JST 2.0 from an old and broken WeMos D1 Mini LiPo Batterie Shield You need to print the round part twice. It fits…
Droopy with his signature line "I'm so Happy" One of Tex Avery cartoons Print with MMU The file has actually 7 colours
My old leaf blower had lost its power and practically only worked on the highest setting. A quick analysis revealed why. The fan blade was completely worn down. I needed a new one. Obviously this fan blade needs a tough filament - I used…
During every party comes the moment “Where did I put my glass again ???” That is all over now - every glass has it's own identifier. No more awkward situation “Is this mine ?” You can use whatever filament you find. The flashier the…
The Jabra Evolve2 65 USB adapter can be fixed to the headset Print in TPU no supports needed
Needed a longer arm for my TP-Link Tapo C100
There is always that somone switching off the Hue lamps on the main button instead of using the Hue Dimmer switch. So I desided to create a cover for this button. There are two versions one for old style T12 and one for T13 with button…
Sign Route 66 Santa Monica - End of the Trail
Liked the design but with maple syrup it was not pratical. I redesigned it to be MMU capable.
The IKEA 365+ storage containers are great as they really close totally. But the lids wont stack. Printed in PLA
Holder for small coke or red bull cans to fix on bed frame 30x30 Added file with small supports
I needed a holder for my Lithium-Ion batteries 40V to fix on the SKÅDIS pegboard The batteries are rebranded for LANDI Okay 40V 2.5 Ah having model number R3-360-AH-U-01 The holder uses a dovetail system ( Skadis Dovetail Peg System )…
Everybody knows the iPhones cameras break easily. Even the sturdy additional camera protection will break. This got too expensive so I created this small, easy and fast printed protection (for the protection). It's supposed to fit under…
Replacement for broken kitchen cupboard door latch Draft version - quick and dirty
New label for the Eaton T0-3-8212 Check out the box for the switch Eaton T0-3-8212 Box
Fix for my Linksys USB3 Ethernet connector that was falling apart.
Box for a Eaton T0-3-8212 switch. Used in my case to control a motor and set forward / backward direction. I used PLA No supports needed but add a brim With 4 perimeters the walls are solid. Check out the new label for the switch Eaton…
I replaced my old standard bird feeder in the form of a house with this one. Since then we have huge numbers of small bird feeding. It took some iterations to get here. Base was the model Deep Cup Bird Feeder from The_Purple_One . I added…
Somehow the tip of one of my sunshades got missing. So I had to create a new one. PETG 3 perimeters no supports inner brim
Sunshade pole cover - in preparation for winter PETG no supports needed
The European Commission started to block the download of radiation data from their site that I was using to get the levels in my region. So I had to create my own sensor. Based on a FTLab GDK101 modul connected with I2C to a Wemos D1 mini…
The front door panel of my outdoor radiant heater Sonnenkönig Phoenix detached often during storms. With this lock this can't happen anymore. You need 1x M4 thread insert in the backplate and 1x M4 x 10 screw to fix it.
Box inlay to store manipulation training ammunition. 6 x GP11 and 6 x GP90
Very sad after 166 years, too much greed, inadequate management PS: not yet printed,
I needed a cover for the standard telephone keys of a Switel TF540. The TF540 is made for elderly people but they still can key-in any number. This cover prevents dialling of unwanted telephone numbers. Only the pre-programmed picture…
Holder for a Remotec ZRC-90 Scene Master using two slots of a Feller EDIZIOdue style switch. Printed in PETG-V0 You need two screws M3*10 and two hot melt inset nuts The holder is very slim and doesn't need a hole in the wall. The one I…
The bottles for the coffee add-ins are made of glass. Not perfect for the marble deck we have in the kitchen. I designed this holder for three bottles so the wont fall over. 2 x 58 mm 1 x 40 mm PETG on 0.25 Draft Prints on Mini 1h less if…
Kanton Thurgau as MMU coaster Diameter 90mm Height 2mm
80mm coaster of Schwamendingen 3 colour design with different layers Printed with 0.6nozzle and 0.15mm height
These are all currently available results.
