P
PrintablesJesseW3D
Amazon Echo Dot Gen 4 Stand
I printed this on my Prusa Mini+ in PETG with 0.2mm layer height, 50% infill, and supports enabled everywhere.
- Downloads
- 1,145
- Likes
- 173
- Rating
- 4.86
All models
Counting matching models…
P
PrintablesJesseW3D
Supportless ID Card / Badge Holder
I printed this in PETG on my Prusa Mini+ with 0.15mm layer height and no supports. Make sure to let it cool before taking it off the print bed so it doesn't bend.
- Downloads
- 543
- Likes
- 57
- Rating
- 5
P
PrintablesJesseW3D
Business Card Holder (Remix)
This model printed very well on my Prusa Mini+. I have not uploaded a photo of a printed model because I added my name on the front and I have no need to print a blank one.
- Downloads
- 338
- Likes
- 17
- Rating
- 5
P
PrintablesJesseW3D
Air Conditioning Redirector
Printed in PETG on a Prusa Mini+ with 0.2mm layer height, no supports (I had them enabled everywhere but none were needed), and 20% infill. I attached it to my air conditioner with hot glue. If you wanted to direct air to the left you…
- Downloads
- 151
- Likes
- 22
- Rating
- 4
P
PrintablesJesseW3D
Post-It Holder
I printed this on my Prusa Mini+ in PETG with no supports, 0.2mm layer height, and 100% infill. This is a remake of AlexT's Post-It Holder .
- Downloads
- 113
- Likes
- 11
- Rating
- 4.5
P
PrintablesJesseW3D
Desk Grommet Pen Cup
I printed it in PETG on my Prusa Mini+ upright with 20% infill (it's a long print so I don't want it to break), with 0.2mm layer height, and supports enabled everywhere. Having the lip at the top to keep it in the grommet creates quite a…
- Downloads
- 106
- Likes
- 15
- Rating
- 0
P
PrintablesJesseW3D
American Silver Eagle Coin Stand
I printed this in PLA on my Prusa Mini+ with 0.10mm layer height and 100% infill. I also put some cork on the bottom so it doesn't slide around on my desk.
- Downloads
- 88
- Likes
- 13
- Rating
- 0
P
PrintablesJesseW3D
Razer Orbweaver Gaming Keypad 20 Degree Ergonomic Tenting Wedge
I printed this in PETG on my Prusa Mini+ with 0.25mm layer height and 4 perimeters. The wedge is a bit shorter than the keypad so it would fit on my small print bed. You could easily extend it but it works well as it is.
- Downloads
- 73
- Likes
- 15
- Rating
- 5
P
PrintablesJesseW3D
Stroopwafel Holder
I printed this in PETG on my Prusa Mini+ with 0.20mm layer height, 15% infill, and supports enabled everywhere. V2 has a rim around the underside so it won't slide off the mug if you move it around.
- Downloads
- 41
- Likes
- 15
- Rating
- 5
P
PrintablesJesseW3D
Van Der Hagen Safety Razor Stand
I printed this in PETG on my Prusa Mini+ with 0.20mm layer height and 15% infill.
- Downloads
- 41
- Likes
- 3
- Rating
- 0
P
PrintablesJesseW3D
Barbasol Shaving Cream Cap (10oz)
I printed this in PETG on my Prusa Mini+ with 0.20mm layer height and 100% infill. I noticed that after using this cap a bit the plastic on my can of Barbasol was a little bit scratched up so expect that, I'm working on a new version…
- Downloads
- 35
- Likes
- 1
- Rating
- 5
P
PrintablesJesseW3D
Gillette Fatboy Adjustable Safety Razor Stand
I printed this in PETG on my Prusa Mini+ with 0.20mm layer height and 100% infill. I only recommend enabling supports in the middle of the underside, if they attach to the outside of the stand, it will be ugly after you remove it. I used…
- Downloads
- 34
- Likes
- 6
- Rating
- 0
P
PrintablesJesseW3D
AMIR Electric Screwdriver Stand with Precision Bit Holder
I printed the stand in PETG on my Prusa Mini+ with 50% infill, 0.2mm layer height, and no supports. For the bit holder I used 15% infill. Update: I made a V2 of the stand which will allow the driver to seat more fully and be removed…
- Downloads
- 32
- Likes
- 3
- Rating
- 0
P
PrintablesJesseW3D
Sakura SumoGrip Clip
I printed V1 in PETG on my Prusa Mini+ with 100% infill, 0.2mm layer height, and no supports. I printed V2 with the same settings except with 0.15mm layer height.
- Downloads
- 25
- Likes
- 4
- Rating
- 0
P
PrintablesJesseW3D
Pegboard Zeiss Lens Wipe Holder
I printed this on my Prusa Mini+ in PLA with supports everywhere using the 0.20mm STRUCTURAL preset with 20% infill.
- Downloads
- 20
- Likes
- 2
- Rating
- 0
These are all currently available results.