Counting matching models…
This is a set of connectors to magnetically attach dust collection hose to tools. This allows you to easily swap one hose between multiple tools without having to adjust hose clamps. I saw another one on Thingiverse, but it required…
Note - There is now a newer version, Wet Plate Holder v5 This is the fourth and hopefully final iteration of my printed wet plate holder. In this version, I've replaced both the mechanical lid closures and the foam light traps with…
This is a simple spline jig for table saws. It comes in two sizes, 200mm width which should fit on most desktop printers and 300mm which is suitable for bigger printers. The FreeCAD file is included and should allow you to customize the…
This is a simple drawer that should fit in the ends of the fence tubing on Sawstop PCS and ICS saws with the T Glide fence. You can just pop the end cap off of the tube and this should fit right in. Pretty much every aspect of this is…
This is a simple block that allows you to arrange your parallel clamps perpendicular to each other for clamping rectangular objects. You can also just use the upper sections as spacers to get your clamps elevated enough to fit cauls…
This is a pair of simple brackets to mount an Incra miter gauge on a wall or other surface. I use two of the normal sized mounts on the outside along with a single one of the shorter mount positioned so that it gets in the way of the…
Print two each of platform.stl and side.stl, which should each print without supports in their default orientation. Slide the platforms into the sides flat end first to assemble. This should hold aluminum and glass plates anywhere from…
This is a simple nesting tray that you can use to store wet plates in water or covered in glycerin for transport back home when you're shooting in the field. That way you can give them a proper rinsing once you have access to running…
This is a stop system for creating repeated cuts of different lengths using a track saw parallel guide system based on Incra T track plus. I have the Precision Dogs set, but Seneca also makes a version and you could conceivably design…
This is the fifth iteration of my 3D printed wet plate holder. My primary goal for this version was simplicity: it requires no hardware or non-printed parts to assemble. The only things you'll need to supply are filament, glue, and your…
I had been using the original T7 shield mount for a while, but needed a place to add a mic receiver so I modified it to include a cold shoe on top. I also scaled the original up by 3% as I found it a little too small to fit my SSDs when…
This is a simple hanger for mounting an ambrotype or tintype to a wall. The model itself is fully parametric so you can easily adapt it to any size using the included FCStd file, but I've provided a variety of pre-sized STL files as well.…
I needed a smaller caddy than the one that came with my dado stack, so I made this printable design. You just print two copies of it, insert a 1/2" bolt into each side, and then glue them together locking the bolts in place. This is sized…
This is a simple little gizmo for precisely calibrating the fence on your Incra miter gauge and returning it to its calibration quickly after adjusting the fence position (e.g. for mitered cuts). The calibrator should slide right into the…
This is a simple head brace you can use to position a model and keep their head still during a multi-second exposure. The fixed arm has a printed baby pin built into it which will slide right into a C stand grip arm. Parts list: 1x fixed…
This is a norsaq I modeled from plans on a now-defunct geocities site , with some small liberties taken with the rounding and the finger indentations to my taste. This is intended to be a functional norsaq, not just a model, although I…
This is a simple little clip I designed to clip onto a kayak paddle with an eyelet for a carabiner so you can attach the paddle to things. I use it to clip my surfski paddle onto my leg leash when I'm standing or floating next to the boat…
I designed this to have a simple way to attach my Tentacle sync boxes to a camera cage with a 1/4" cap screw. Every variant of this model should print without supports, standing up on its end the same way it's oriented in the STEP file.…
This fits Chamonix 8"x8" lens board cameras and adapts them down to Sinar sized lens boards. You'll want to print one copy of sinar.stl and four copies of toggle.stl . You'll also need 8xM3x4x5mm heat set inserts. Install the eight…
These are protective bulb covers for Speedotron black line heads, specifically the older 10x models (102, 105, 106, etc.). The design is a little bit messy as I reverse engineered the mounting plate from a scan of a speedotron reflector,…
These are all currently available results.
