Counting matching models…
Desiccant bag is inside the spool - ensures good contact with support rollers and constant filament tension even if the spool is nearly empty. Used material: Filament consumption approx. 40g 4x ball bearings 625 2x M3x8 DIN912 1x…
Fixing the key blade when not kept in the opened position. Removable.
Safety disclaimer: Use only materials certified for food contact Wash all prints by warm soapy water before use Keep children under 3 years of age under supervision while playing with prints Models were sized to avoid choking hazard (ISO…
Small Seastar for sensory play. Scaled to avoid choking.
Clownfish for Sensory play. Scaled to avoid choking.
Seahorse for Sensory play. Scaled to avoid choking.
Printed from standard PETG, cubic infill 25%. No special tricks needed.
Used for grids made by: BulldogBite https://www.printables.com/@BulldogBite_121940
Narrow funnel has also fine ribs pitch - fine ground coffee is better to use or shake a little bit when inserting the ground coffee. Tested on DeLonghi Magnifica S.
The original hole in the back cover for 4015 fan was enlarged for 6025 fan. As reference the bottom and left corner (looking from back to front) was of 4015 fan was kept - i.e. the hole was enlarged up and right. Fan duct is attached…
corner joint for attaching the aluminum extruded profiles
Octopus for Sensory play. Scale to avoid choking.
Crab for Sensory play. Scaled to avoid choking.
Material needed: 2 risers (it is symmetric, just print 2 pieces) 30 pcs of oak lamellas for example:…
Material needed: Photoframe with 2mm glass and plastic frame (mine was bought in Pepco) 2x M3x40 2x nut M3 neodym magnet dia5x3mm 1x M3 magnetic screw replacing the stainless steel one in the frame of UM2
Simple holder for holding the Oral-B in IKEA Tisken corner shelf.
Made from Abaflex PLA blue.
Made from Abaflex PLA blue.
LED light bar / light ramp designed for 3Dsets Landy Winchtruck but in general can be used for any RC car from 1/8 to 1/12. Designed for Super flux LED 7.62x7.62x2.5mm. In my case 3.2V@20mA version used powered by 6V system:…
Many variants of the scheme is available and all is working. One these is below: Used material: PCB 100x50 https://www.gme.cz/v/1508537/cu-ta-040-univerzalni-spoj-vrtany-100x50mm LM317…
Print part by part and stitch together by the CA glue.
Two 40mm holes have to be made to the rear panel - to the bottom part of the “chimneys” for stepper motors. Fans blows the air up and cools the steppers. Material needed: 2x fan 5010 24VDC 2x fan grill 40mm 1x DC controller with feedback…
Use 4 pieces of M3x6 screws to attach the label holder through the mesh eyes. Start in the corner with rounded hole, continue with the slot holes. Better to use laminated paper or thick paper labels instead of common copy paper label.…
It has quite big clamping force and can squeeze the teflon tube - adjustable by tightening the M2 (DIN912) screw. Used for avoiding the tube slide from the defined position. It is recommended to use only on straight parts of the tube as…
Vertical stand for Hewlett Packard HP Z29G
The first make of my 8 years old son who made his first CAD model
Simple holder for holding the Philips Sonicare Kids in IKEA Tisken rectangular shelf.
Recommended to use brim - contact surface is very tiny
Simple protective sleeve to avoid damage of the bottle bottom part Print the calibration ring firts to test the fit. Using the Sunlu PLA and Abaflex PLA+ on Qidi Q2 were firts time right on nominal dimension - very light press fit.
screws orientation inverted screws fully covered to provide electrical isolation For screws M3x8 or longer (dependend on counterpart thickness, hole depth 7.5mm) Used for car battery cover repair NOTE: use fire retardand material if used…
Tyres - type B (24x80x33mm) https://www.aliexpress.com/item/1005005993991795.html?spm=a2g0o.order_list.order_list_main.35.55921802jtZ9TF Rim is bigger then the inner dia of the tyres - can be easily streched and gluing the tyres is not…
Use standard fans 3010 (30x30x10mm). Attached by 4x M3x16 screws. Just replace the original Hood Lock by the modified one - install the fans first. Compatible with standard 3Dsets Landy winch.
Use glue to keep the top on the tube. Tube clamped to the roll frame using clamp with M2x6 scew (DIN912 or ISO 7380) and M3x6 screw to the triangular panel in the front frame.
Beadlock ring which can carry the 70g grams of the additional weight. Squeezes the tyre bead as much as possible and acxeptable with respect to the PLA rims. Recommendation from the original creator: To add the extra weight, I used these…
Choose the CW or CCW version depends on dominant direction of the rotation (i.e. forward cruise). Designed primarily for Turnigy Aerodrive 3536 outrunner. Modify the hole for the rotor shaft flange and/or the contact contour shape based…
These are all currently available results.
