Counting matching models…
I recommend printing the 3mf since it has all the models in the correct orientation. You can also scale the model to your liking. Assembly is just inserting the 2 pins in the holes and putting the top on. The side the top is facing…
This is a working model of a spring. I printed this with 100% infill, although you don't need to (higher infill = stiffer spring). Printed with supports (not possible without them). Disclaimer: You need to keep in mind that you are…
CAD file . The supplied models are separated based on meter width, in this case 19mm and 21mm, close to the most common widths, at least from what i could find, i had a 19mm. These values are the maximum meter width that will fit. If you…
This fit 220x220mm bed like ender 3 or bigger. Assembly is pretty straight forward, just remove the support on the tree and slide it into the base.
This is a coin you insert into a shopping cart so that you can unlock it. Its basically a plastic clone of 1 euro coin. I printed this with 0.1 mm layer height using pla. I got the keychain from this link:…
Flower pot in the second picture. The pot can be inserted into any flower pot you would like, that's why there is only a basic one. The diameter of the pot at 100% is 6cm and the tolerance on the pin is 0.2mm. To make it fit into the…
This is a small model of planetary gearbox, which will help you to understand how planetary gearboxes work. Assembly instructions: 1. First print all of the models you see on the picture (all of the stl. files you see in files tab) 2.…
Maz-537 has functioning suspension, doors and a removable flatbed. No supports slicer supports, except for wheel mounts and beams. All the other parts that need supports have them built in. All the parts fit smaller build plates like…
The thinnest part of the opening pick is 0.3 mm. The spudger is 0.5 mm. Printing: Opening pick: 0.1mm layer height, 100% infill. For the other ones just default settings.
This can be used on direct drive extruders. Tested on ender 3 s1 but should work on Prusa MK3, too. I didn't use magnets, I just put it on the shaft using the hole on the back. Don’t forget to check out my other models too.
This is a holder for a broom. You can mount this on a wall, inside a wardrobe etc. To mount this you need strong double sided tape or epoxy (strong tape worked for me, but if you find a better way leave a comment) Step 1: Put the tape on…
You can use the supplied stl file which works fine for most applications. However you can change some parameters in the cad file if you want. Printing: Print the model in this orientation. No supports needed. I recommend printing this out…
I wanted a joystick i could use with games like farming simulator or flight simulator, but i didn't want to buy one since i am planning to incorporate it into a farm sim side panel. And i find it fun making my own stuff. Printing: The…
All the hardware i will be using is necessary for the stock version. Though you can modify the parameters to fit your screws and bearings. I opted to use bearings since it makes the whole assembly pretty much silent. It is also very…
This is small and neat filament cleaner. Its made from 2 parts. To make this work: Step 1: Print both parts and try if filament fits trough small holes if not drill them out with right drill bit. Step 2: Take a sponge and cut a cylinder…
If you want to modify the parameters, use this link . You need to have an Onshape account to download and edit it otherwise it is view only. No supports are required. For the labels i just made a table in Word, wrote the types and cut it…
Everything needed to assemble this is inside the assembly instructions.
This is a luggage tag where you can write your information and if your luggage will be lost on airport they would know who it is. It have design of a suitcase. And its printed in two parts which clicks together. Then you just cut a…
Simple modification to the Yves Chaudron's pistachio bowl to remove the need for supports.
Printing: Import the file into your slicer. Set bottom and top layers to 0. Based on your preference you can set the perimeters, i set them to 4. I recommend printing infills that are well secured, but you can experiment. Mine were…
Here is the CAD file . Using it is quite simple. Just push like you see in the video with slight wiggling. Then you can just pull out the staple.
This model is only for show and isn't supposed to be used to actually squeeze oranges, since it is 3d printed. Printing: Import the model into the slicer, scale it to the size you want and rotate it by 180 degrees on the X axis. Then…
CAD file . There are 3 different sizes, all have a spacing between notches of 1cm. After printing it use a bit of rotation force on the hinges and they should break free.
Printing: Flip it 180 degrees on the Z axis. And paint the supports roughly on these places. There is also a 3mf file with the supports ready.
There are 4 different sizes supplied. These refer to the inner diameter of the salt shaker. The one i printed is 10mm. If you also want to change other parameters, like length of the salt shaker, refer to the CAD model section. Printing…
This set contains all chess pieces that are styled as Easter bunnies. They were all modeled in blender. No supports necessary except for the knight.
Print all of the three parts and assemble them. Assembly: Insert printed Floor.stl into the base from the threaded side. Now the top part serves as dice storage. If you turn it around (bottom upwards), you have a dice roller from that…
CAD file . Printing Make sure the top notches for stacking are facing down. Other parts are in the correct orientation. Or just use the 3mf files. Assembly Make sure the door moves freely when moving in both parts. If not, sand down the…
Print both of the files included and just join them together. Happy printing
The inside diameter of the pot is 55mm. The inside height is 57mm. So you can scale it in the slicer to fit your needs.
This model is made to be as small and have most information as possible. Its completely universal model. The shaft can hold up to 10 filament samples. The cap is inserted into the shaft so the filament samples wont come of. The cap should…
Simple and modern pot for 3 plants in a row. I used succulents. Printed with Wood PLA filament.
CAD file . There are multiple different sized holes supplied. If you need bigger or specific size, you can change a parameter in the CAD file.
Simple holder that just slides on. I recommend putting double-sided tape on the right side as shown in the third image. Print it in the orientation it is. No supports needed.
Please note: Flip the model around in the slicer.
CAD file . The modules are printed separately and you can just insert them into the base. You can also make your own modules, all the parameters are in the CAD file.
This whole model is parametric so you can modify the size to your liking. The models included are just basic sizes. File . You can modify the amount of rows, row diameter, tolerances, module length…
The stand fits a candle with diameter of 22mm.
CAD file If the models supplied don't suit your needs you can change the parameters, like rows, columns, size of the compartment itself. The one in the image is 2x4 tray.
Open the .f3d and .step files in a cad program for modification of the model. I used Fusion360 to make this, but you can use any software. If you find any problems with the model feel free to write in the comments.
The premade models are based on the bambulab magnet sizes, up to 15mm diameter. If you want different sizes of magnets you will need to modify some parameters. It is very easy, though. All the parameters are explained in the onshape…
These are all currently available results.
