Counting matching models…
Hoping to be lightweight modular miniature storage and transport for magnetized miniatures. I use steel striking blanks in the slots to allow the miniature to attach. The lid can be secured with rubber bands to make a decently robust case.
Simple modular CD stand. I just glue them together with CA glue (carefully) and add some feet on the bottom.
Easy to print paintbrush holders that do a decent job of aligning and retaining small paintbrushes.
Miniatures Painting Handles that just use friction for a rotating platform. (Print with random start and stop points) Should be fine to print with fuzzy skin for extra grip. I use steel striking blanks and fabric tape for miniature…
A painting handle with a rotating platform that spins on bearings and is restricted by a ball plunger. The rotating platform is assembled with two bearings and a long M4 screw. I used an M6 ball plunger although it can be used without…
The magnet slot should be about 0.00260000 m deep and 0.01210000 m in diameter. I made it for a vindicator tank but I presume it would work with others. It has textures to help with adhesion, I use a two part epoxy just to be safe.
To increase the height of an LG 42 Inch C2 Display on your desk. Has spots for rubber feet on the bottom. A few different heights.
Some different styles of miniature painting handles. Older designs without any rotation. Magnets on the bottom to prevent them from falling over is recommended as some are off balance.
Allows for attaching an ~10x1.75 magnet to the bottom of halo flashpoint miniatures by mantic games. Using a textured plate is probably advisable (I did not)
I modelled these for other projects, probably not exact but close enough for what I needed. Never printed them, only used them for modeling.
I have put 3/8 inch dowels through the small diameter texture rollers made by CustomMiniatureMaker sold through/printed by only-games.co and I made these to organize and protect the rollers. These are stacking trays that keep them…
Designed to allow for white/grey/black coverage on pro acryl and standard bottles using a clip-on printable mask that allows them to be striped up in batches. There is also a version with a textured bottom to use for speed-paints which is…
The handles attach to the rollers using 5/8 wooden dowel sections cut to size and glue; I use foaming polyurethane glue i.e. “Original Gorilla Glue” as it will fill the gaps nicely and form a solid bond. The spacing rings will be VERY…
Spinning Top Holder (7 ForeverSpin, ForeverSpin Station & one Vorso Mk1) It has spots for rubber feet on the bottom. A holder for my random assortment of spinning tops. The tolerances are too big.
You should use a piece of plastic straw, but if you don't have one you could use this to protect your small paintbrushes for transit.
I wanted to attach some stronger magnets to my warcrow models so I made this adapter to attach the 8x2.75mm (often ordered as 8x3mm) magnets
A stand for very specifically holding "Travel in the desert sea" miniature by Neko Galaxy Miniatures. I suppose if you had a similar miniature that was intended to be suspended by an 5mm rod from the back it could also work for that. Made…
Holds the standard small size IPA bottles with the cap, can be mounted with Command Strips to a wall
For use with an M6 ball plunger to create the clicks when rotating.
Provides pegs to organize in-progress painting projects when using cobalt keep painting handles
I decided that increasing the base height to fit 3mm thick magnets was too much so I made this slimmer version that is for 8x1.75 or 8x2mm magnets. Note that the magnets will not fit perfectly and so you need to use a small ball of…
Designed to represent a speedball using a 25mm token in the center to represent the type of speedball. For Infinity the miniatures game N5 by Corvus Belli.
In the Corporate Appropriation mission, it can be difficult to remember which objective is which, these help.
A dolly for moving a specific type of drop leaf table by socketing in Y junction and feet and having caster wheels on the bottom. The caster wheels are the ones that come with SIDIO skates so they are M6 holes spaced at 53mm x 24mm
These are all currently available results.
