All models

Counting matching models…

Wall mount for DeWalt DCS356 Oscillating Tool

Wallmount for DeWalt DCS356 Oscillating tool

Downloads: 792
Likes: 129
Rating: 5

Camelbak Drying Stand

Drying stand for Camelbak and other hydration reservoirs - base is a water bottle/mug/cup drying stand by itself. Works for 2L and 3L bladders

Downloads: 786
Likes: 126
Rating: 4.77

Order a print of this model

PrintablesDivideby0

Center console drawer for 5th-Gen 4Runner

Printable drawer for bottom cubby in 5th-Gen 4Runner center console. Supports recommended for the pull handle only Recommend adhesive-backed felt on the bottom and rear corners for best fit. RAM ball variant available here:…

Downloads: 687
Likes: 58
Rating: 5

Order a print of this model

PrintablesDivideby0

Wall mount for DeWalt DCS334 Jigsaw

Wallmount designed for DeWalt DCS334 Jigsaw v2 - updated to improve fit with protective plastic cover on base

Downloads: 597
Likes: 87
Rating: 4.33

Order a print of this model

PrintablesDivideby0

Wall mount for DeWalt DCG412 Angle Grinder

Downloads: 546
Likes: 56
Rating: 5

Order a print of this model

PrintablesDivideby0

Wall mount for DeWalt DCW210 20v random orbit sander

Downloads: 465
Likes: 60
Rating: 5

Order a print of this model

PrintablesDivideby0

Altoids insert to hold LTT Screwdriver bits

Altoids insert to hold LTT Screwdriver bit sets - holds 4 sets (48 bits) Note: to avoid rattling, the insert will need small shims on either long side (it has to be smaller than the opening to fit past the rolled edge); I used the end…

Downloads: 319
Likes: 64
Rating: 4.67

Order a print of this model

PrintablesDivideby0

CPAP hose drying hook

Drying adapter I designed for the Resmed CPAP hose - fits shower fittings 20mm or less in diameter

Downloads: 290
Likes: 52
Rating: 5

Order a print of this model

PrintablesDivideby0

Tripod Wall bracket

I wanted a better storage solution for my tripods and other support gear than piling them in a closet, so I designed these wall mounts to hang them from the ball head. Large: 25mm throat, 75mm clearance under the plate Standard: 20mm…

Downloads: 214
Likes: 40
Rating: 5

Order a print of this model

PrintablesDivideby0

Steamdeck dock snap together version

A snap-together version of the Steamdeck dock. This variant is currently untested Changelog -v2 released: revised geometry based on user feedback for easier assembly

Downloads: 134
Likes: 12
Rating: 4.33

Order a print of this model

PrintablesDivideby0

Tool mount for Mellif cordless hot glue gun

Mount for Mellif cordless hot glue gun

Downloads: 96
Likes: 23
Rating: 5

Order a print of this model

PrintablesDivideby0

RAM mount for 5th-Gen 4Runner

It uses M6 hardware for the front plate and fits RAM ball RAP-B-354U-TRA1. I used Cat tongue tape on the bottom, center, and corners to keep it from sliding out,

Downloads: 69
Likes: 10
Rating: 5

Order a print of this model

PrintablesDivideby0

Wall mount for DeWalt DW3742C Jigsaw blades

Downloads: 60
Likes: 9
Rating: 0

Order a print of this model

PrintablesDivideby0

Divider for 3rd-gen Toyota Sienna Cupholder

Lost the original part years ago, so I designed this to replace it. Recommend placing felt on either side for a tight fit without any rattling while driving. Note: print upside down to avoid needing supports

Downloads: 60
Likes: 6
Rating: 5

Order a print of this model

PrintablesDivideby0

RAM Mount adapter for Yaesu FTM-500DR remote head

RAM adapter for Yaesu FTM-500DR remote head. It matches the RAM-B-347U base. Uses all M5 hardware with Nyloc nuts. Support is only needed for the center M5 bolt that attaches to the back of the remote head. V2 model available in 2…

Downloads: 59
Likes: 11
Rating: 5

Order a print of this model

PrintablesDivideby0

Low Beam cap wrench for 5th-gen 4Runner (2010+)

Wrench to remove the weather cap when replacing the low beam bulbs on a 5th-gen 4Runner. The orange model in the photos was the prototype - red is the final design. Holes are for a screwdriver shaft to gain extra leverage if needed

Downloads: 51
Likes: 10
Rating: 0

Order a print of this model

PrintablesDivideby0