Counting matching models…
Fully Metric Remix of "Better Chisel Sharpening Jig" by @GarageTimeDavid_3790 Changes: Adjusted hex holes from ¼" (11.1125 mm) to 10 mm to fit M6 bolts Adjusted round holes from 8.4 mm / 6.4 mm to 8.0 mm / 6.0 mm respectively
Saw a video of a similar hair parting tool called “The Braid Aid” by “AB Glitz” and thought this should be easy to model and print. Prints in two pieces for stability reasons. Just superglue them together. Print orientation can be seen in…
Replacement of the upper yarn guide of the “ SENTRO 48 Needles Knitting Machine ” When using mine with a drill adaptor the yarn quickly cut into the original guide which made it useless as the needles did not catch the yarn anymore.…
Outdoor case for the Sonoff SNZB-02P. I just taped the orange, magnetic mounting plate inside.
Cookiecutter for 5x “Vanillekipferl” Onshape: https://cad.onshape.com/documents/b4b8dffa1d6271a7f0230799/w/b8f5b23d53fd90cfd7752206/e/191f8b9cbb65d791594cac79 Like the model? Consider saying thank you by buying me a coffee:
Original: https://www.printables.com/model/824217-shelly-wall-switch-adapter-for-jung-cd500-with-com The original multi segment frames did not quite fit. While the 2 segment version was just a little tight, the 3 segment version did not…
Cup & remote holder for the IKEA VIMLE sofa/couch (standard width armrest). Uses a printed Skadis board to allow for flexible attachment of holders. I deviated from the original Skadis hole geometry very slightly to make the overhangs…
Remix of the Candy Cane by @BeetleBuild . Two changes: I cut the cane into pieces so that a small section of the bottom can be colored, resulting in a fully colored cane. I made the cut pieces 0.4mm thick. Thus with 0.2mm layer height…
Just some decorations saying “FRÖHLICHE WEIHNACHTEN”. I printed them face down on my textured printbed to get a nice surface. The STL contains 3 separate bodys: “FRÖHLICHE", “WEIHN”, and "ACHTEN” This allows splitting the model in the…
Replacement part for the "Messeraufnahme" / motor to knife coupling for Monsieur Cuisine Plus / Silvercrest SKMK 1200 A1 This model fits very snug and should hold without the snap ring. The snugness should make it last a little longer…
Skadis beer holder using two of the “universal hook” by CSD_Salzburg Remixed from “IKEA Skadis Beer Holder” by Chillkroetchen . Used my primitive Blender skills to reduce the inner diameter from 80mm to 72mm while leaving the mounting…
Small saddle square. Based on https://www.thingiverse.com/thing:1481552 . Inspired by https://www.axminster.co.uk/veritas-saddle-square-ax480278 . Main changes: smaller size riffled surfaces clearance in the corner Designed in Onshape:…
Remix of Stokke Tripp Trapp Front Foot by @koy00_249879 . I removed the pins as they did not fit my chair (it was close though). Attached with hot glue
Modified two parts of the “Scratch Me Spider”: made the base 1.5mm thicker so it does not break as easy made the knob easier to grab / more ergonomic
Remix of "3D4U by Miele Flexi nozzle" by @miele_3D4U to enable better print orientation for long nozzles. I wanted to print a long, thin nozzle for cleaning inside my car, but because of the layer orientation in the original the nozzle…
Replacement part for the joint on my "Walimex WT-3131 Basic-Stativ" tripod. Designed in Onshape: https://cad.onshape.com/documents/56650c33d9ff2bc4b6eadadb/w/25c530232c5c8e16d42c6b2e/e/d91081d30246aae3d34dd405 Like the model? Consider…
Adapter to attach the NoseFrida to a 34mm vacuum. I tested it on my skin and the suction is no harder than what I can produce with my mouth. Therefore I deemed it safe for use on a baby. Just makes it easier when the baby is sick. After…
Remix von diesem Modell von "ManneM": https://www.thingiverse.com/thing:7015589 Motorplatte und Wellenadapter sind unveränderte Kopien (hab sie der Vollständigkeit halber mit hochgeladen) Der Wellenmitnehmer war mir viel zu dünn/fragil…
These are all currently available results.
