Counting matching models…
This is a mount for Black and Decker powerconnect 18V batteries for storate on walls or shelves. two versions. one with holes in the wall because I like the look.
Have a candy jar at work but don't want everybody use their fingers. Print instructions Category: Kitchen & Dining
Had to many 1/8 inch (4mm) hex bits lying around and made this for storing them on a wall. Added a version with holder for my screwdriver (22mm diameter Ferm CDM1140) Print instructions Category: Tool Holders & Boxes
Pull the edges of your blanked through the cross and put the spike in the ground. Print instructions Category: Outdoor & Garden Print Settings Infill: 100
the pods have dimensions of 10mm outside and 8 mm inside so maybe others fit too
If you are like me, you have various bins with nuts laying around from projects you want to sort into sizes “one day”. But never will…. Or you are Makerella and your evil step brothers wont let you go to the Makers Faire before those nuts…
Present for a friend but I thought others might like it too. its a clone of the fenix mini vaporizer i think.
Simple holder for 8mm linear rails on 20mm aluminum extrusions. No supports and the zip tie acts as a guide for the middle of the extrusion Print instructions Category: 3D Printer Parts Print Settings Rafts: Doesn't Matter Supports:…
I needed an mount for my Z axis endstop. Placement has to be precise to hit the sensor so I made them movable. All 3 are usable even if I in the end did only need one. Print instructions Category: 3D Printer Parts
Remix of the great https://www.printables.com/model/347077-cat-bookmark I just added the butthole.
Simple holder for a Nintendo switch joycon grip and joycon wrist straps. Can be placed on a shelf, table etc or attached to a wall. (I used superglue to add it to my controller board) Can be printed without supports. Print instructions…
Dual VWheel Dummy for use in designing parts Print instructions Category: Parts
Simple mold to make silicone dampers for your heatbed instead of springs. I did use 2 component duplicate silicone (200°C safe), which did get off the mold really easy. 2 versions. One with printed pillars for the holes and one with holes…
you need: a spring (like from a pen) m3 screws a m3 heatset insert for the probes: a piece of metal like a small nail, pogo-pin etc. and some wire. The one with the wider tip can be used to make custom flashing jigs for devices.…
Got a new accu for my ebike and the threads on the frame did not fit. My frame has a oval diameter and is 33mm thick. The brackets fit on it quite well. You also need M5 screws, washers and nuts matching your frame. On the pics shown are…
Catch those fast little fellows without hassle. The shrimp get sucked into the tube and put into the basket where you can collect them with the basket and put them into a new tank or whatever. Print the basket and the net holding ring in…
I needed feet for my Hypercube project and was to lazy for threading holes in the extrusions. So I designed corner Brackets with 4 holes and feet which also add stability to the frame, Bonus: If you put them on top of the cube or whatever…
simple wall mount for my daughter's wake up light. You can sling the antenna around it so it won't dangle from the wall. Print instructions Category: Tool Holders & Boxes
Childproofing the doors of our cabinets without damage. You also need nuts, washers and a m8 threaded rod. Look at the pics it should be self explainig. A hole-less version of the backside is included so you can just drill your own 8mm…
Adjustable mount for BLTouch. Parts needed: 1 M4 screw for leveling, 1 spring (not to weak) 1 Injection nut M4 outer diameter 6mm 1 M4 washer (goes between screw head and plastic of course) Fit is quite tight so maybe you need to adjust…
there is a second version with a hole for hanging it up
With google shutting down Stadia in Januar 2023 there will be a lot of controllers without a way to wirelessly connect them to the PC (If google doesnt decide to open the Firmware. And its a well made sturdy one from which there will be…
I used the encoder hole from https://www.printables.com/model/356728-encoder-knob
Those tiny little dwarfes always playing with your lightswitches? Make them accessible from above only. I used hot glue to fix it to the wall . Theres an extension for when they grow or you misjudged the lenght needed. Print instructions…
Mount for my Tapo TC60 cam to mount it in a grow tent with 16mm poles
These are all currently available results.
