Counting matching models…
The most ideal way to print is vertical and supports for the controller interface, I've printed flat and for me at least it hasn't worked out as well. Lastly I printed with a lot of perimeters for strength and 5% infill.
I use my GO as a UMPC so a lot of times I don't use or have my controllers connected. I also like my Xbox controller a bit better than the GO's Controllers anyway. This will cover the sides, but I make no promises it will protect from…
I have not printed this design, but would try flat first. Vertical might be a pain. I'd assume you'll need supports if vertical, but for horizontal you'd still need supports for the controller interface. I would print with a lot of…
The most ideal way to print is vertical and supports for the controller interface, I've printed flat and for me at least it hasn't worked out as well. Lastly I printed with a lot of perimeters for strength and 5% infill.
This would probably be better printed vertically to make the controller interface teeth as strong as possible. I recommend lots of perimeters and little infill. I did not print this model, but it is the same as my angled versions.
Using a old belt I had (see link below for one like it) I replaced the stock hard plastic handle and made covers for the top and bottom opening. Recommend printing in a filament that is UV resistant and Heat resistant. Best way for my…
Printed in ASA was the best for me, but choose whatever filament you like. Did not try TPU so don't know how well it would fit. Printing Separately and painting supports on the Hinge side at the ends will keep the curved end shape better.
Would be better to print vertically if possible vs flat on the bed. Added a gcode to illustrate.
This is a Vertical Holder for a Tube of Toothpaste. Modeled for a Crest toothpaste tube cap, but as long as the widest diameter of the cap is 17.15mm or less it will fit without sticking to the cap. I print exclusively with ASA, but use…
Slim Bumper version of the Surface Duo 1 bumper I uploaded. This is based off someone that owned a Duo 1 in which they were fine with the fit. This is two sets of bumpers. One leaves the button area and all the usb area open. The other…
Keep important papers together and organize.
Toyota MR2 Spyder HVAC knob (This may fit other Toyotas of the same gen, not sure). There is a indication hole, and will work fine as is or can put a small diffusing tape over the back.
I sleep in complete darkness and usually tape all things that light up in my room. The Ethernet cable port is harder cover up so made a cover for the lights instead. Photo of Device has duck tape residue.
***Simple Bumper for the Surface Duo 1, BUT… I modeled it off the Duo 1 stock bumper as I do not have a Duo 1 any more. PLEASE let me know how the fitment is, because I'm unsure of how it will be. *** Printed in ASA was the best for me,…
This Bumper has an extended area around the perimeter so when fully open it supports the screen from flex because of the camera bump. Printed in ASA was the best for me, but choose whatever filament you like. Did not try TPU so don't know…
Parent's old garage refrigerator doesn't stay closed so a quick fix. Best part you open and close the doors as you normally would. Used 3M double sided tape to stick to the side of the refrigerator.
If you've downloaded the MR2 Spyder Pull Strap Covers, but only using the upper cover for a loop style pull strap and want to cover the bottom hole completely.
This is a Surface Duo 2 case, but also has a holder for a Uogic Pen. I don't own any of the Microsoft Surface series of pens and assume none of them fit as the Uogic pen is a unique shape and size. I do recommend it as the battery life is…
Note: I do not own a GRC, made this for a friend that owns a GRC. They confirmed the fit to work in their shifter set up.
Got tired of the cable bulk so I got a male to male usb c adapter and made two kinds of braces for the SanDisk Extreme Portable SSD. Mostly for when I'm connecting it to my laptop. One brace is just for the usb c adapter the other brace…
This Bumper has an extended area around the perimeter so when fully open it supports the screen from flex because of the camera bump. Printed in ASA was the best for me, but choose whatever filament you like. Did not try TPU so don't know…
This mount will work on the steering column plastic (Toyota or similar shape) for a Scanguage II. Confirm works on a Toyota MR2, Matrix, and Vibe.
These Plugs defeat the whole purpose of Sony Link Buds and make them more like traditional ear bud head phones.
The GemRed 82305 Digital Angle Finder Protractor has some Sharp AF edges so this not only protects the tool, but protects everything from it's sharp edges. Great Tool otherwise! This was printed in two pieces because it doesn't fit on a…
This is a bumper to go over the screen, ideally to prevent a screen protector film from pealing up during use. Will work for only a Apple iWatch which is 44mm (iWatch 4 and earlier?)
Pretty solid the more perimeters that are used. Size limited by my Prusa Mini. I printed with ASA, but use whatever filament you like although TPU might not be ideal.
This bumper has more coverage as it covers the Sim card slot and also protects the opposite side of the USB port. ***Simple Bumper for the Surface Duo 1, BUT… I modeled it off the Duo 1 stock bumper as I do not have a Duo 1 any more.…
Please download and print this if you got my Surface Duo 2 Case as it was suppose to be included. See picture for placement on the slicer to have a smooth face. Printed in ASA, but use whatever filament you like. Haven't tried TPU, but…
I was gifted a Yeti Rambler (Dick's) and none of the accessory lids fit. This is cover goes on top of the slip lid and makes more "leak resistant". I can't claim complete leak proof.
I was gifted a 20oz. Yeti Rambler (Dick's) and none of the accessory lids fit. This is cover goes on top of the screw top lid and makes more "leak resistant". I can't claim complete leak proof. Bonus is the cap makes it ALOT easier to…
This cover slides over the button to hit the garage door opener (open or closed) so you don't accidentally hit the button while holding the remote. You will need to heat up the clamping part so that it's tight to the remote. See the…
These are all currently available results.
