Counting matching models…
This is a simple clip-on cable tag that can be used for labeling or marking round cables of assorted sizes. The label inserted into the tag must be about 0.5mm wider than the selected cable size. I have also included the Fusion 360 file…
Simple spiral fidget toy. Enjoy just pushing the parts through each other in a twisting motion. No supports or other special printing requirements. The angle is high so that printing of the overhangs is quite easy.
This is simple bracket that I designed for the Fortigate 40F. The bracket from Fortigate is very expensive and it is actually very bad from Fortigate that such an expensive device is not rack mountable. Assembly needs two M3 countersunk…
This is a simple square insert for an ammunition box. I printed the box and the insert in ABS to allow for higher temperatures during storage. The print as shown is for 9mm Parabellum ammunition. I used the parametric box from Yanev (Tool…
This is a simple holder for an AA battery with banana plug connectors. I printed the holder in PLA+, but it should work well with ABS. Just make sure that your interlayer strength is good. No supports required. To remove the battery from…
This model is best printed with the bottom of the cups on the plate. This requires a significant amount of supports, but the design does not allow for other options. I used ABS to print it to be able to handle high temperatures when the…
This is a simple side mount for the ADXL345 accelerometer board for the Voron 2.4 Afterburner head. Some of the other mounts are fitted to the front fan shroud of the head, but this section of the head is not very rigid and may result in…
This is a simple slot cover for the Misumi HFSB5-2020 aluminum extrusion typically used for the Voron 3D printers. 20x20 Aluminum Extrusion - 5 Series, Base 20 | MISUMI | MISUMI (misumi-ec.com) Note that the cover is only 100mm long and…
Printable downlight fitting for a GU10 lamp. The springs holding it in place and the spring holding the lamp in the fitting needs to be taken from an old fitting. I used these to replace the fittings in the bathroom since these were…
I bought a license disc holder, but it was difficult to get the disk out when it was time to replace it. The strip for the double-sided tape was very narrow and caused the double-sided tape to come loose after a while. I designed this…
Updated printable downlight fitting for an LED GU10 lamp. The springs holding it in place and the spring holding the lamp in the fitting needs to be taken from an old fitting. I used these to replace the fittings in the bathroom since…
Printable model of the pink trolley as part of the Checkers Little Shop collection. Supports and assembly are required.
I bought a Mellow CNC Tap for a Voron 2.4 only to find out after fitting it that I did not order the bracket for the Hall magnet on the X axis stop. So, I designed this bracket. I hope it helps somebody else in the same situation.
Simple snap together case for a Raspberry Pi Pico W with a DHT22 temperature and humidity sensor. I programmed the Pico via ESPHome to provide the temperature and humidity readings to my Home Assistant installation.…
Template for cutting the wheel arch on the body of a 12th scale RC pan car. The template has a 45mm radius and allows for 0.25 compression on the foam wheels.
Template for cutting the wheel arch on the body of a 12th scale RC pan car. The template has a 44mm radius and allows for 0.25 compression on the foam wheels.
This handle can be used to lift boards up to 20mm in two ways: by hooking it at the bottom of the board or at the end of the board. For lifting at the end of the board a rubber tube over the center pin may be required. If you need to lift…
Wall mount/holder for Centurion remote with two screw holes for garage door or sliding gate. Remote just twists into position and can be removed without unscrewing the mount.
Template for cutting the wheel arch on the body of a 12th scale RC pan car. The template has a 46mm radius and allows for 0.25 compression on the foam wheels.
This is a case for 12 sets of the ride height adjusters (372070) for an Xray X12 RC race car.
This is a simple bracket for hanging a ToolkitRC P200 power supply underneath a shelf. There is also space underneath for the power cables.
Simple model for a golf ball template with emoji. It is going to be a long day! Supports required.
This is a Fusion 360 model for the Ride Height Adjuster for an Xray X12 21 (may work for other versions as well). You can specify the required offset as you like. I have created a set that fits in between the offsets that comes with the…
This organizer is part of a set that I am busy creating for our complete cutlery set from eetrite. Kitchen & Dining Products | Eetrite
Samsung PowerShare on the Galaxy phones are great. It allows you to charge your watch from the phone without carrying an additional charger. My problem is that you cannot use the phone while charging the watch. It is also almost…
This organizer is part of a set that I am busy creating for our complete cutlery set from eetrite. Kitchen & Dining Products | Eetrite
Flexible front bumper for an Xray X12. The front of the bumper lines up nicely with the edge of the body. Printing with 100% infill with ABS is recommended.
These are all currently available results.
