Counting matching models…
This is a remix of Micke's Simple Sanding Block with Brainanator's cornering remix, plus my own remix of curved end. This will allow this sanding block to be useful for flat surfaces, inner corners and contours. I also shrink the model so…
A two-in-one shopping cart token for Canadians. One side is Loonie token and the other side is Quarter token. The Quarter side has been tested with carts at Save on Foods. The Loonie side has been tested with carts at Walmart and T&T.
This is an easy-to-install version of Tesla Model Y's 2nd row seatbelt guide. You just need to snap it onto the head rest rods without the need to take them out (which isn't straightforward if you don't know how). I also found the…
This is a simple air freshener box with two halves to be snapped together. You can DIY air freshener using baking soda and essential oil mix (tons of recipes online), wrap that with tissue paper or non-woven fabric cut from a disposable…
This is a drum sticks holder for electronic drum sets with 1.5 inches (38.1 mm) o.d. tube frame. This frame tube size is very commonly seen on Yamaha, Roland and Alesis electric drum sets. The drum sticks holder is designed to clip onto…
Most Gaggia Classic owners are dealing (or living) with a dripping steam wand because the steam valve's metal-to-metal seal will break down over time. This drip chute will collect the water drops and send them to the drip tray. This drip…
A minimalist razor stand inspired by Harry's aluminum block stand. The inner hole shape roughly matches the Truman handle. There is 0.4 mm tolerance around so it is easy to get the razor handle in and out without binding. Printing with…
I found my eero 6+ has a very warm bottom. The temperature measures to about 50 C. I'm worrying this could have an impact on either the longevity of the eero itself or my table top. So I designed a ring style base to fit the chamfer of…
A two-tone TPU ring. Print the ring body with TPU, and the accent band in any material/colour you prefer. Snap the two parts together to make a two-tone ring. The model provided has an inner diameter of 20 mm. Scale accordingly to your…
Inspired by the original model, I made funnel and tamper for Bialetti Musa 2 Cup moka pot. It will probably fit other Bialetti stainless steel models (2 cup size). Note the tamper is not intended for compacting the coffee grounds. It…
I have a cabinet with glass panels. The clips holding the glasses are broken so I modelled a simple one for easy printing and drop in replace. The model is specifically designed to be less rigid so it can bend a bit even printed with a…
This is a simple grocery bag hook in the trunk for Tesla Model Y 7 Seater. It sits on top of the third row seat, and has an insert between the head rest and back so the head rest can hold it down. The hook does not require the head rest…
Simple S hook that is not too large or too small. I created honeycomb pattern in the body as an exercise in Fusion 360. The wall thicknesses are small enough (1.2 to 1.6 mm) so that infill doesn't matter. Everything should be wall lines.
Simple replacement of the cable clip on my Mic Stand's boom arm. The model's size is for an arm with 14.5 mm diameter. It holds cables up to 8 mm diameter. You may need to measure your boom arm's diameter and scale accordingly.
This is a hanging tag of a Canadian Flag (Maple Leaf Flag, l'Unifolié). The red part of the flag are raised so it is friendly for manual two-colour printing.
This is a holder for T-shank jigsaw blades. It is suitable for blades with thickness from 1 mm to about 2 mm range. All the Bosch jigsaw blades I have fall into this range. I'm publishing this model ahead of Halloween. I hope this can…
This is a simple dog poop bag holder that can fit most rolls on the market. The inner space size is 40 mm diameter and 60 mm height. Most rolls are around 35mm diameter but a few I came across are around 38 mm. This holder will fit them…
I want to add additional shelfs for an Ikea cabinet, but found the holes for shelf pins on that cabinet is around 3.4 mm in diameter. This is a really hard-to-find size. Most common shelf pins are 5 mm. So I made a model to print the body…
This is a low profile drip tray designed for Gaggia Classic. It's half the height of the original drip tray, and fit completely within the original drip tray foot print. At the same time, it maximize the capacity within its dimensions.…
I have been using a Soarer's Converter for my IBM Model M keyboard. The converter was made from a Pro Micro board and I originally built a small wooden box for it. But the lid of the wooden box could no longer stay on after years of wood…
A hexagon pen holder with alternating "windows", as a re-creation of my woodworking project. Print in vase mode.
This is a steam valve protection disk model for Gaggia Classic. It has a split design so you can have a M2 screw and nut to have it tightened. I have two versions created. One can go directly to the steam valve. The other has a slightly…
These are all currently available results.
