Counting matching models…
These are the fully custom parts that I have created for my LetsRobot.tv robot named Bottington. I created these parts to allow me add accessories to Bottington at any point in the future without having to redesign the frame. These parts…
This is a straight driving ETV (Egg Transport Vehicle) for the 2015 division C Science Olympiad, Scrambler. It should be fully rules complaint but check dimensions before using this design. Note: At time of upload, the design has not been…
This is a steerable ETV (Egg Transport Vehicle) for the 2015 division C Science Olympiad, Scrambler. It should be fully rules complaint but check dimensions before using this design. Note: At time of upload, the design has not been tested…
This is replacement part for the Robotgeek Gripper to allow for easier collection of pennies for the 2017 division C Science Olympiad event, Robot Arm. It should be fully rules complaint but check dimensions before using this design. The…
The Hub Bub Odd is a very simple Wind Power wind turbine for the 2017 division C Science Olympiad, based on the original Hub Bub . It should be fully rules complaint but check dimensions before using this design. The Hub Bub Odd is an…
This a Egg Backstop (aka the egg block) for the 2015 division C Science Olympiad, Scrambler. It should be fully rules complaint but check dimensions before using this design. Best way to attach it is glue. Note: At time of upload, the…
This is a very simple Wind Power wind turbine for the 2016 division C Science Olympiad. It should be fully rules complaint but check dimensions before using this design. The Hub Bub is an easy to attach hub that allows 1/8" wooden dowels…
This is a very simple adapter to use a CD/DVD as a lightweight wheel with a #8-32 thread rod axial. This was designed, to spec, for the Hobbs High School Science Olympiad Team. It was used as part of the second place Gravity Vehicle.…
The RoadRunner is a simple to build modification of the Tomahawk Electric Vehicle. Both the RoadRunner and Tomahawk were Electric Vehicles built for the 2016 division C Science Olympiad. The purpose of the RoadRunner is to create a much…
This is a replacement motor mount tab for the Makerfire 4-wheel drive robot chassis. These tabs have been tested on my robot for the past 5 months (over the winter of 2017-18) and have been holding up better then the one that came with…
Parts to launch the ETV (Egg Transport Vehicle) for the 2015 division C Science Olympiad, Scrambler. It should be fully rules complaint but check dimensions before using this design. 2015/2016 redesign: To make it easier to launch the…
This is a simple wing rib for the 2014 Science Olympiad event, Wright Stuff. The length of the rib is 66 mm and it is 1.5 mm thick. Category: Engineering
This is a proof of concept for a geared braking system on the 'gravity vehicle' for 2013 division C Science Olympiad Competition. This is / can be made fully rules compliant, with the 2013 rules, with very little modification. Note: This…
This is a very simple, in line, Robot Arm extenders that fit onto the RobotGeek's V.2 Robotic Arm for the 2017 division C Science Olympiad. It should be fully rules complaint but check dimensions before using this design. The BeefyArm…
This is a very simple It's About Time metronome / pendulum clock for the 2016 division C Science Olympiad. It should be fully rules complaint but check dimensions before using this design. The Clunky Clock is designed to use parts I have…
This is a bolt on set of extensions that fit onto the OWI-535 Robotic Arm Edge for the 2017 division C Science Olympiad. It should be fully rules complaint but check dimensions before using this design. The Gamma Mods are designed to…
This is a straight driving Electric Vehicle for the 2016 division C Science Olympiad. It should be fully rules complaint but check dimensions before using this design. Note: At time of upload, the design has not been tested in competition…
This is a slide on set of gripper/extensions that fit onto the OWI-535 Robotic Arm Edge to allow for easier collection of pennies for the 2017 division C Science Olympiad. It should be fully rules complaint but check dimensions before…
This is a very simple, in line, Robot Arm extenders that fit onto the RobotGeek's V.2 Robotic Arm for the 2016 division C Science Olympiad. It should be fully rules complaint but check dimensions before using this design. The Armlong will…
This is a simple ring to add fins to a ping pong parachute pressure vessel. This is a very basic design with a 41.90 mm inner radius. The fin slots are designed to fit card stock. To make it fit your pressure vessel, scale it. Print…
This is a very basic air duct for use in the Hovercraft event for the 2017 division B/C Science Olympiad. It should be fully rules complaint but check dimensions before using this design. The Aero Kinetic Redirector or AKR for short (my…
This is a very basic bolt on set of extensions that fit onto the OWI-535 Robotic Arm Edge for the 2013 division C Science Olympiad. It should be fully rules complaint but check dimensions before using this design. The Alpha Mods are…
These are some 3d printed stands that are designed to adapt AeroGarden Harvest gardens to Style Selections Steel Utility shelving units . This allows to garden to sit level on the wire shelving unit and be resistant to being bumped off…
This set of parts improves a few minor annoyances I have with Parallax's small robot kits (ActivityBot and Cyber:Bot) and are designed to help the small robot kits preform better in the 2026 division C Science Olympiad event, Robot Tour.…
It is build-able in its current form but some updates will be forthcoming to add a larger percentage of the missiles skin. Print 1x Comms 12x grav 1x Impeller Block 6x Impeller Inne 12x Impeller Node 6x Impeller Outer 12x Impeller Part B…
This is my entire into the r/3dprinting's re:3d design contest. I have designed a pair of tool holsters that will make one of my job duties much easier. Ever so often I am required to do utility Line Locates for the municipality I work…
The Chip-E Universal Expansion Kit (Chip-E UEK) is a set of replacement parts for the RobotGeek 'Chip-E' - Open Source Arduino 3D Printed Robot . The Chip-E UEK (Chip-E Universal Expansion Kit) was designed for the Chip-E Remix Chanage .…
These are all currently available results.
![[RobotGeek V.2] BeefyArm - Robot Arm Mod (2017 Science Olympiad)](https://media.printables.com/media/prints/219412/images/1998845_8d9dcac3-700a-4640-94c3-ad54b9e58640/d98898f287af5f5cf4b9cd00b4ad35d4_display_large_21.jpg)
![[RobotGeek V.2] ArmLong- Robot Arm Mod (2016 Science Olympiad)](https://media.printables.com/media/prints/219409/images/1998817_7b06f363-0ac3-4a22-8d61-53b833f0590c/06f143485f34d95685ca062f6f0eecf9_display_large_21.jpg)
