Counting matching models…
Designed for Ender3v2 to mount behind the LCD screen. I would imagine this works with other Ender 3s but I cannot confirm You'll want to use supports for the rails If you're looking for a mount to go in middle to replace the drawer, see…
Redesigned joint cone loader based on https://www.thingiverse.com/thing:5356953 I made this one more compact and modular depending on the size of your cone This model was created for the king cone which is 109mm but you could easily…
Remixed the original 5015 fan duct and slimmed the left duct down to make room for the CR Touch Also added a slot for an M3 nut to utilize the rear mounting hole from the original duct Category: 3D Printer Parts
Remix of new Satasana dual fan duct with Ender 3v2 mounting hole
LED light bar for the top of the Ender 3 (or v2) Print each piece with the flat side down (I printed at 0.2 resolution) and attach at the center Fasten with T-nuts (I used these: https://www.thingiverse.com/thing:3050607) Run the wires up…
This is a bracket to make a spray bottle holder to be affixed to the inside of a cabinet door This was designed for a ½” dowel, cut to whatever length you desire I attached this heavy duty double sided tape and super glue for extra support
Container / Dispenser for freezer (Ziploc) bags Prints in two pieces and snaps together Doesn't need supports if printed with the flat sides down
Insert to convert the Utopia Cereal Containers (with indentations) into a filament dry box. Desiccant box prints separately and snaps into place (so it can be swapped out or dried separately).
Wall mount for amber soap dispenser bottle print on its side (you want the layer lines to run through the whole object). no supports necessary, but a raft would help ensure that the rounded edge on the bottom doesn't get cut off Bottles I…
Filament Guide for Reality Ender 3 Filament Runout Sensor Requires - 1x 608 Bearing (I used this ) - 1x M3 screw, at least 14mm - 2x M3 screws, at least 18mm…
Hooks that fit between the rear panels that can be used for a cargo net or other storage Category: Automotive
Surface Mount AirTag Holder intended for discretely attaching an AirTag to objects like skis or a snowboard. I can't claim watertight-ness, but I submerged it in water and I didn't see any make it inside. Also the AirTag itself is IP67 so…
Tesla key card holder for center console of Model 3 and Model Y Note: It doesn't look too great in the photo because I tried sanding it and it dulled out the black Double note: if you print in PLA, it will warp in the sun Category:…
Gallon sized freezer bag container for Gridfinity No supports needed, print at your largest layer setting where the layers are still strongly adhered (I used 0.3mm) The bin and lid print in two parts to accommodate most bed sizes. They…
Quart sized freezer bag container for Gridfinity No supports needed, print at your largest layer setting where the layers are still strongly adhered (I used 0.3mm)
Driver bit for Multiboard T-Bolt which can be coupled with a hex driver bit or a 3D printed 4mm shaft
MagSafe style mount for use with these magnets: https://www.amazon.com/gp/product/B09FZ5Z7S4/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 The mount is adjustable via ball socket If you plan to rotate your phone a lot, I would recommend…
Articulating iPhone MagSafe Stand with optional Watch / AirPods Charger Print the MagSafe holder, nut, and spacer. And then your choice of the base (with or without watch charger). Only the MagSafe puck holder needs supports. Use at least…
Flex BL Drill Bit Holder uses the stock screw and can mount behind the belt clip Intended to be printed with embedded magnets (8mm x 2mm round) - two per slot I used the ones from:…
Smaller adjustment knob for the Ender 3 (and probably more) build plate These knobs were designed to be much smaller than the existing ones for setups that have auto leveling (as the knobs aren't needed much and shouldn't be accidentally…
Phone clamp for tripod 44mm quick mount system Heavily inspired by this model , however I modeled this entirely myself as I don't like modifying STLs (and I enjoy projects) The screw cap must be glued onto the threaded rod (make sure to…
Flex BL Drill Magnetic Screw Holder attaches to the back of the driver Intended to be printed with embedded magnets (32mm x 2mm round) I used the ones from: https://www.amazon.com/dp/B09WZTSQ9Y?psc=1&ref=ppx_yo2ov_dt_b_product_details…
Note: not the most attractive thing I've designed, but I tried to do it in a way that it's not really visible (originally I wanted to stick them to the flat outside part). Hooks that allow you to use your mask over your AirPods Max…
These are all currently available results.
