Counting matching models…
Construction site accessories europe style. Fence Road safety beacon TL base plate If you want to print the fence in one piece, your print plate width has to be ≥250mm. If you want to print the road safety beacon without supports, move it…
20litre plastic cansiter for 1/14 scale. For best result, print them as shown in the picture
Pallet rack for 1/14 Lesu forklift and Carson EUR pallets. A middle part takes 3 lengthwise or 2 widthwise pallets. You need two print 2 side and 1-3 middle pieces for one rack. Holes in side parts are closed (easier to print). Middle…
Traffic light for 1/14 scale for 5mm LEDs. You can glue front and rear part together or drill tiny holes (1.2 mm) into the front part, then glue mount part into rear part, hold the front part and drill smaller tiny holes (0.8mm). Then…
Air scoop for a Suzuki Samurai If you print it splitted, you need a 40x90x2mm plate to connect booth pieces.
Roof Rack for a Tamiya Land Rover Defender 90 body (58657, 51607, 58700, 47478). You need 22x 2x6mm tapping screws and 8x M2x10mm screws, M2 washer and nuts. Drill all vertical holes of RoofRack and RoofRackTop with a 2mm drill. Drill all…
This is a 1/10 scale camping folding table. Since I had already a chair, this had to be done. Features: - Folds up tight and compact for easy storage. - Easy to print without supports. To complete this build you will need the following M1…
Case for LILYGO T-RGB round touch display development board. There is a cutout for usb connector and sd card You need 4 pcs M2 threaded inserts and M2x20 (v1 M2x8) sink screws to mount the rear lid. Also some thin foam (sponge rubber) so…
With this adapter you are able to mount a QuicRun 1060 switch to a Tamiya chassis. You need 4 2x6mm tapping screws and 2 washer. If you got a light unit with your Tamiya kit there are some leftover screws.
1/10 Trailer axle for MST Diff. unit. For one axle you need 2x diff axles (from MST Rear axle 310109 or MST Diff. unit 210591 ), 4x 5mm e-clips, 6x 8x5x2.5 ball bearing (tamiya 850 ball bearing) and 8x M3x8 countersunk screws. You need to…
Front and rear bumper for Tamiya Land Rover Defender 90 Body. There are some mounting holes for a winch and the front bumper itself. For the bumper mount you need 4 M2 threaded inserts. You need 8 2x8mm tapping screws to mount the bull…
Reinforcement and Wheelholder for Tamiya Land Rover Defender D90. Replaces the polycarbonat pieces “rear brace A” and “rear brace B” (instructions page 15, step 30). Drill holes and use double-sided tape as described in the instructions.…
Mud flaps for Tamiya Land Rover Defender 90. I used an old bicycle tube and cutted it with my printed templates. You need some tiny screws (i used M1.4x5mm) and double sided adhesive tape for the mount. Front mud flaps follow soon
Micro servomount for Carson trailer hitch . I use a Savöx SH-0253 micro servo and the shift rod from tamiya volvo fh16 timber truck kit.
Connects two Ikea LAGKAPTEN tables if using it with BOAXEL. So you just need one leg. You need 5 M4 threaded inserts and 5 short M4x10 Screws with washer to mount the leg. To mount the adapter, you can use the screws comes with the legs.…
A simple cat vomit sign You need two pieces and should enable support. You need a 6mm rod or something similar and 4 zip ties to complete this build
A cover for the upper bed-head and sideway mounting holes. You need 4 pieces each.
Legs for the Cooler Master MasterBox Q300L case. If your case is permanent full of dust because it have to stand on the floor you can use this legs. You need 2 pcs, 8x M4 threaded inserts and 8x M4x8 Screws (optional with washer). Just…
Tamiya Jeep YJ Wrangler Spare Wheel Mount for rim with 12mm hex adapter. You need a M4 threaded insert and a M4x15mm screw
Roof Rack for MST Jimny J3 body shell. Its designed for a specific LED bar you can get on amazon or any 100mm width led bar. Take a look at the pictures For mounting you only need some zip ties
Replacement for Servonaut LV7FH16 daytime running light lens. I broke all the replacement lenses from this kit… so i decided to print my own. Use transparent filament and small nozzle (0.2 - 0.4)! Print 2 pieces, one mirrored. You have to…
Remix for Lenovo ThinkPad L14 or similar (28mm spacer) and USB-C Dock Gen 2 (40AS0090xx or similar) instead of 120mm fan. I used M4 threaded inserts for plastic and melted them into the modified spacer. With four M4x8mm screws i mounted…
If you own LiPo racing packs which are slightly longer then their NiMH/NiCd counterparts you need to modify the battery holder of your CC-01. I decided to let the original quick release (part E2) untouched and modify the back side. You…
Shorty Battery Adapter for Kyosho (Turbo) Scorpion or similar. The battery box from some Kyosho 2WD legendary series kits is made for standard stick pack size batteries. If you want to use shorty batteries, you need to fill the empty space.
Spare wheel holder for 1/14 Rastar Land Rover Defender. You can mount 1.0" wheels with a 7mm hex. You need a M2 threaded insert and a countersunk M2x8mm screw. Also another screw to mount the wheel. Be careful with disassembling the stock…
You need 6pcs M5 threaded inserts and 6pcs M5x16mm countersunk screws. But you can also replace the mid part with thread rods or something
A spare wheel mount for MST Jimny J3 body shell. You need 4pcs M3x10mm countersunk screws and 4 locknuts. You also need a M4 threaded insert and a M4x10mm screw for the spare wheel
Case for RC Light Controller . You need 4x M2x4mm screws to mount AW9523 and 4x M2x12mm countersunk screws for the case. For the LED hole you need a piece of transparent 1.75mm filament. Use a piece of duct tape to cover the back of the…
GoPro Mount for Kyosho Scorpion and Turbo Scorpion. Just replace it with the gearbox cap. You need a short ¼" screw, threadlocker, a tripod mount and some sponge rubber. Also you should set infill to 100% around the ¼" screw to reinforce…
1/14 Tool Attachment for Small LESU Wheelloader (AT1050/MCL8) and Skidsteer (LT5). There is a basic tool version and a compact version you can add to your creation available. Please respect license and use the remix feature if you upload…
These are all currently available results.
