P
PrintablesPlankto
Tesla CCS2 Wall Charger Plug Holder
This remix has been altered to fit the CCS2 plug type found on the Tesla's that are sold in Australia, should fit other cars with the CCS2 type plug.
- Downloads
- 845
- Likes
- 94
- Rating
- 4.75
All models
Counting matching models…
P
PrintablesPlankto
Morse Code Key
Morse Code Key created in OpenSCAD using magnets instead of the spring for the return. BOM: M3x5mm Screw M3x8mm Screw M3x10mm Screw M3x25mm Screw M3 Locknut 2xM3 Nut 3x M3 Washer 2x 623 Bearings 2x 8mmx2.75mm Magnet 3.5mm Panel Mount Jack…
- Downloads
- 422
- Likes
- 64
- Rating
- 5
P
PrintablesPlankto
Ford Ranger Next Gen Accessory Panel
Accessory panel for the rear tub of the Australian Ford Ranger adding dual anderson plug and dual 12v accessory sockets. Print in 2 parts, add 8x M3 nylock nuts to back section, add the anderson plugs mount to panel and add the accessory…
- Downloads
- 262
- Likes
- 32
- Rating
- 5
P
PrintablesPlankto
Wire Insulator - Dipole / Wire Antenna
Wire insulator for wire antennas, dipole etc. Category: Hobby
- Downloads
- 115
- Likes
- 17
- Rating
- 5
P
PrintablesPlankto
Wemos Cube Lamp
My version of a colour cube lamp using a Wemos D1 and a 8x8 LED Matrix. Wemos is flashed using ESPHome firmware and connected to Home Assistant https://www.home-assistant.io/ for control. I've also added the template I'm using in ESPHome.…
- Downloads
- 79
- Likes
- 16
- Rating
- 0
P
PrintablesPlankto
2.2" TFT Desktop Stand Crypto / Stocks Ticker
Adapted to suit a 2.2" TFT Hardware: ILI9225 SPI Screen Wemos Mini D1 Added Arduino sketch for the Crypto Ticker. Updated to use yahoo finance symbols. Category: Electronics
- Downloads
- 78
- Likes
- 16
- Rating
- 5
P
PrintablesPlankto
Printed Dipole Centre Insulator
3d Printed Dipole insulator Light-weight and ideal for temporary portable operation with some wire and zip ties. Recently tested and used with a 80m doublet used portable during a 24 hour contest. Print Settings Printer Brand: RepRap…
- Downloads
- 71
- Likes
- 6
- Rating
- 0
P
PrintablesPlankto
uSDX+ Transceiver / AT100 Carry Box
BOM: 24x M3 Brass Knurled Heatset Inserts 20x M3 8mm SHBC 6x M3 18mm SHBC Optional Double-sided tape between frame and uSDX and AT100
- Downloads
- 64
- Likes
- 5
- Rating
- 0
P
PrintablesPlankto
Poke Ball Plus Automatic Catcher for Pokemon Go
Poke Ball plus stand and vibration activated automatic catcher used with Pokémon Go. This thing will detect the vibration pulse when connected to Pokémon Go and activate the arm to press the button to catch the Pokémon. Materials used:…
- Downloads
- 62
- Likes
- 17
- Rating
- 0
P
PrintablesPlankto
Holden VH VK Bonnet Grille Clips
I lost my original clips somewhere so designed these replacement ones in openSCAD
- Downloads
- 60
- Likes
- 3
- Rating
- 0
P
PrintablesPlankto
Holden Calais VK VL Boot Garnish Clip
One of the clips was broken on my boot garnish for the Calais trim on my VK so I have remade it in openSCAD I printed it rotated using organic supports from ABS filament as the clip will be weak is left flat on the build plate.
- Downloads
- 47
- Likes
- 1
- Rating
- 0
P
PrintablesPlankto
Stand for Aliexpress Mini Tesla Coil
Model is to suit the Aliexpress version of the PCB. https://www.aliexpress.com/item/33056971078.html Print, Add the brass standoffs to the base then screw the pcb down.
- Downloads
- 39
- Likes
- 4
- Rating
- 5
P
PrintablesPlankto
Holden VK Door Wiring Grommet
I lost the original grommets so created these as a replacement part. Print in flexable filament and cut one side to facilitate installation. To suit Holden VK commodore but should fit VB, VC, VH, VK, VL
- Downloads
- 33
- Likes
- 0
- Rating
- 0
P
PrintablesPlankto
ZMR250 Antenna Mount
Slight redesign to fit the ZMR250 Carbon frame, rebuilt in OpenScad from scratch. Category: R/C Vehicles
- Downloads
- 21
- Likes
- 4
- Rating
- 0
P
PrintablesPlankto
Motorbike Antenna Mount
Here is a antenna mount I made to suit a 2m/70cm whip antenna attached to the number plate of my motorbike. Printed in PET-G Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: Yes Resolution: 0.2 Infill: 30% Filament:…
- Downloads
- 16
- Likes
- 3
- Rating
- 0
P
PrintablesPlankto
Hailea AC0-308 Rear Pump Housing
I dropped the pump and the rear housing broke, this was created to replace the damaged rear housing.
- Downloads
- 13
- Likes
- 2
- Rating
- 0
P
PrintablesPlankto
Jumbospot / Zumspot Raspberry Pi Zero Wireless Case
This case is to suit the Jumbospot Pi hat for the Raspberry Pi Zero W found on eBay which seems to be a clone of the Zumspot. Created in openSCAD if you need to customise. Print the 3 parts Insert the Pi into the lower piece Press the…
- Downloads
- 12
- Likes
- 1
- Rating
- 0
These are all currently available results.