Counting matching models…
I tried a few other planter designs and in the end found it more time efficient to design and print my own with speed and overall ease of printing in mind. This still isn't exactly time optimized but was still faster to print than some…
This is my original take on the Joy Fidget by TomoDesigns. I wanted to print one but then realized I could elevate the experience by adding a really satisfying clicker underneath. "Where do I get a clicker though?" you may ask. Look no…
WARNING: Due to the Kobra Max hot end mounting screw locations this adapter requires modification of top shoulder the Revo 6 heat sink. The image below shows overlap of the Revo Six model provided by E3D and my adapter. The mounting…
This was a learning project for me that I will be updating as I make it more useful. This is a ~50:1 gear ratio with the flex spline having 90 teeth and the output casing having 88 teeth. The cool thing about these gearboxes is that they…
This is a portal button I made some time ago. The button portion moves freely on rails inside the base. I designed it to use as a toggle switch to control a relay that would power the monitors I use on my desk so I wouldn't have to reach…
A dust port compatible with the Dewalt DW735 planer.
This is a very versatile little dowelling jig. I designed it so that I could complete a custom furniture commission and made every one of the ~100 dowelling holes with this one jig. I have incorporated some updates since I used it based…
I wanted some bench cookies but nowhere shipped them fast for a reasonable price. Amazon sells foam with 2 day shipping and I have a printer. Improvise, adapt, overcome. What you will need: 5/16"-18 Flanged Hex Nut 1/8" Adhesive Backed…
The photos with bellows installed show the original size bellows. The +5mm bellows maintain contact with the arm 100% of the time and move significantly more air.
This is a direct replacement for a 2002 WRX sun visor clip. Mine broke at some point and rather than source one and have it shipped I decided to model my own. I printed it way-back-when on an Affinia H480 with "natural" colored ABS and it…
This is a print in place hinged glasses case. I recently bought a nice pair of glasses that only came with a soft case and I decided making my own hard case would be a great way to practice print in place hinges. This model uses four (4)…
This prints very easily in PLA .2mm quality profile with brim. If you print without brim you will likely have a bad time as the print bed contact area is very small. The model does work but it is VERY fragile right now since I tried to…
A basic riving knife for the standard riving knife mount on the Grizzly G1023S Table Saw.
Glue helps keep things in place. But what keeps the glue in its place? That chemical cabinet or junk drawer you have it in seems like things always get pushed to the back, knocked over, lost, etc. Why not give it a place to live? Your…
Just a slight modification to allow Robithicas 123 block box to be pushed open with a thumb.
These are a drop in replacement for and work well with the standoffs that come on the Bessey K-Body REVOlution Parallel Bar Clamps. In my use case I needed more support on the face of my glueups so I designed these to augment the provided…
These are NOT easy to connect, but it is necessary to have a friction fit once it is connected.
This is a replacement part for the rear center seat belt cover in a 2002 Subaru WRX. When tested it proved to be a snap fit with no modification. I broke this while fixing my back seat and couldn't find any online through Subaru or…
The flip out L shaped cable winding fixture on Apples power bricks.
I recommend printing with as sliced with a 0.4mm nozzle. The model should be fully dense. We did have to clean up the round hole on the bottom side with a 5/32 drill bit for a very good fit.
We had a pineapple corer part break. This was an easy printable fix! It is used in a plastic Pineapple corer were ~15mm.
Polymer structure of Acrylonitrile Butadiene Styrene (ABS)
This fits the OEM elastic band mounted clip Wahoo provides with the RPM SPEED sensor. I uploaded a variety of lengths so you can find what length provides the correct amount of stretch for your hub and your shore hardness of flexible…
These are all currently available results.
