P
PrintablesPali
Lego train re-railer
I did not found a re-railer for lego (other than track pieces), so I designed one. In case You need some changes, just let me know, I will do my best…
- Downloads
- 462
- Likes
- 101
- Rating
- 4.89
All models
Counting matching models…
P
PrintablesPali
Manta 2017 RG65 sailboat
This is a remix of https://www.thingiverse.com/thing:2572866, to accomodate Molineasails Keel, and swing rig. This remix is basically only for the midship section and the keel box, to accomodate Molineasails swing rigs and keel-rudder…
- Downloads
- 460
- Likes
- 39
- Rating
- 5
P
PrintablesPali
RC model waterproof boot vase mode
To waterproof pushrods on Your RC model, print in vase mode. You can adjust the size of the “exit” part by scaling or adjusting the line width in the slicer, may be a tight fit to seal properly. I used silicone grease on mine to be a bit…
- Downloads
- 224
- Likes
- 35
- Rating
- 5
P
PrintablesPali
Orchid clip
My Wife told Me to use My printer for something useful, so I designet it for Her. Idea is based on the one from henryk, but with slight modifications. I made 2 versions, both of them fits a 5 mm bamboo rod, the bigger opening is 10mm, so…
- Downloads
- 153
- Likes
- 31
- Rating
- 5
P
PrintablesPali
Wave wooden railway track
My Son asked Me so I designed one.
- Downloads
- 144
- Likes
- 39
- Rating
- 5
P
PrintablesPali
RC sailboat sheet pulley 8mm
To fit Footy, Micro Magic, RG65/DF65 class RC sailboats. Works fine even without ball bearing (They may get rusty and just make trouble anyway). The diameter of the pulley is around 8mm, a bit bigger than the original DF or MM pulleys,…
- Downloads
- 135
- Likes
- 15
- Rating
- 0
P
PrintablesPali
DIY laminator
This laminator is based on Makers Mashup model, but made from scratch see: https://www.youtube.com/watch?v=UfSaZ_dAfy4 I use it to laminate stickers, but can be used to laminate signs or so. The model uses 4 pcs 6203 2RS bearings, and 1pc…
- Downloads
- 129
- Likes
- 32
- Rating
- 5
P
PrintablesPali
2014 Toyota Rav4 dashboard trim phone mount, Quadlock compatible
To complete one mount You will need: rav4-phone-holder-v4_quadlock (one piece, I do not recommend to print this due to the lost details of the splined portion which is the interface for the Quadlock system). or: rav4-phone-holder-v4_base…
- Downloads
- 117
- Likes
- 10
- Rating
- 0
P
PrintablesPali
Boat stand RG65
I needed a storage for My RG65 RC sailboats, which fits into a small place, but can hold 3 or more boats securely. You have to buy inexpensive plastic tubes which are used for external wire routing, can be purchased in DIY or electrical…
- Downloads
- 104
- Likes
- 7
- Rating
- 0
P
PrintablesPali
Mandala drawing helper
If someone likes to draw mandalas and would like to divide a circle to equal segments. This template is designed for 18 holes (20 degrees from each other), with a center hole for alignment, and a cross mark on the top for easier…
- Downloads
- 86
- Likes
- 46
- Rating
- 0
P
PrintablesPali
Low poly Dart Wader remix
This is a simple quick remix of Low poly Dart Wader from CalebTimoteo see: https://www.printables.com/model/553476-darth You have two options: 1: print the original model and print separately the insert cup then glue or just leave as is…
- Downloads
- 70
- Likes
- 15
- Rating
- 5
P
PrintablesPali
Xp-Pen artist pro 16 drawing tablet VESA mount
The main goal was to be able to use the above mentioned pen tablet as a secondary monitor when not used for drawing, but still be able to remove it easily from the VESA (100x100mm) mount when necessary, by flipping up the two side locks…
- Downloads
- 68
- Likes
- 18
- Rating
- 0
P
PrintablesPali
Condense water collector for kitchen extractor 150mm tube
I designed it for My Co-worker due to condensation in His kitchen extractor during winter. The outer diameter of the connector pieces are 150mm, but STEP and F360 files included for easier adjustments/modifications. Printed from PETG for…
- Downloads
- 61
- Likes
- 8
- Rating
- 0
P
PrintablesPali
Lidl wooden train level crossing repair
Print the two halves, join pieces with filament pieces and superglue. I tried to print from one piece but failed to insert the gate, but I upload the single piece file in case if You prefer to cut at other location. Printed from PLA,…
- Downloads
- 52
- Likes
- 10
- Rating
- 5
P
PrintablesPali
Pine cone shaped advent wreath candle holder
If You use candles never leave them unattended due to fire hazard! This is a remix of the pine cones to fit 21mm diameter candles and to mount on a wreath (I made mine from 2,85mm filament due to a bad order and discovered after opening…
- Downloads
- 50
- Likes
- 12
- Rating
- 0
P
PrintablesPali
Litophane holder night light
Litophane holder to hold 120x90x3mm pictures. Originally designed to have a more uniform light of a night light in a childroom. Press fit for the light what is on the picture. I added aluminium tape on the inner side of back wall as…
- Downloads
- 45
- Likes
- 8
- Rating
- 0
P
PrintablesPali
Orchid pot support
This support is intended to avoid tipping over during blooming of orchids. The numbers suggest the diameter x height of the pot which fits inside. You may need to slightly resize in the slicer if You have a different pot. Printed from…
- Downloads
- 38
- Likes
- 12
- Rating
- 0
P
PrintablesPali
Footy insignia and country code
I designed these stencils for easier sail marking, with additional country code (I may do Yours on request :) ) I added a small gap to the bottom against paint creeping. The country code is 40mm high (acc to Micro Magic rules), however…
- Downloads
- 34
- Likes
- 4
- Rating
- 0
P
PrintablesPali
RC sailboat rig identification letters
Drawing template to identify rigs on RC sailboats, letter height 20mm. i haven't find one so I made it. I use for RG65 class.
- Downloads
- 34
- Likes
- 3
- Rating
- 0
P
PrintablesPali
SV08 screwless fan decoupler
The mainboard fan is annoyingly noisy on the SV08 (not to mention the other fans, but a different topic), so I installed a quiet fan with a buck converter and hoping the best, but it did not change dramatically. I was searching for the…
- Downloads
- 33
- Likes
- 2
- Rating
- 5
P
PrintablesPali
Minimal design modular Orchid vase support
The flowering season of orchids just begun. Common problem after flowering, They tend to tip over due to flowers. This may resolve this problem, by inserting the flowering pot into this support, acting as an outrigger. Print and assembly…
- Downloads
- 31
- Likes
- 4
- Rating
- 0
P
PrintablesPali
Prusament bird feeder top 50 deg. overhang
This design is based on this: https://www.printables.com/model/58212-improved-prusament-spool-soda-bttle-birdfeeder , but the overhang decreased to 50 degrees to allow supportless printing upside down, the diameter slightly increased too.…
- Downloads
- 28
- Likes
- 6
- Rating
- 5
P
PrintablesPali
Chilli sauce inverter
I found some similar devices here, but did not fit My kind of Chilli, so I designed one. This device used to help to extract the last drops of Your favourite Chilli, to save environment and help World peace… :) There are two versions:…
- Downloads
- 27
- Likes
- 2
- Rating
- 5
P
PrintablesPali
Footy rc sailboat measuring box
This box complies with the rules of Footy class Rc sailboat. The rule You can find here: https://footy.rcsailing.net/rules.php If You design or just build a Footy it is a useful tool to check out if Your boat fits the rules. I think the…
- Downloads
- 24
- Likes
- 3
- Rating
- 0
P
PrintablesPali
Koh-I-Noor 24 colour water/aquarel paint holder
Designed to fit the above mentioned brand (may fit others), for easier handling and orientation. (those paint disks are not really removeable, thrust me, look on the white one) I originally designed with 4 small dimples in each cutout to…
- Downloads
- 24
- Likes
- 8
- Rating
- 0
P
PrintablesPali
Mechanical counter, count back wheels
Please find other parts at the original model.
- Downloads
- 17
- Likes
- 6
- Rating
- 0
P
PrintablesPali
Ticket inspector sign
Used to give permission for the train to leave the station, used by Ticket inspectors on Hungarian railways. Can be used as an accessory for costumes. I recommend to resize for children. Printed in white PLA, painted with Revell 364
- Downloads
- 9
- Likes
- 0
- Rating
- 0
P
PrintablesPali
Master dehydrator/drier replacement carbon filter holder + bonus repair clips
To replace the expensive OEM carbon filter with a cheap one used in kitchen extractors. This device clips to the grill under the diverter flap but does not block adjustment. Use commonly available cheap carbon filter mat available in…
- Downloads
- 8
- Likes
- 1
- Rating
- 0
P
PrintablesPali
29mm hex driver for mixer tap insert
This tool is intended to help with the removal and installation of mixer tap inserts with 29mm hexagonal faces. The original tool is made from plastic, but with much thinner walls and of course was not available when needed… Before use I…
- Downloads
- 4
- Likes
- 1
- Rating
- 0
P
PrintablesPali
Hettich pull out table adapters
Made a simple remix to use shorter and different diameter screws, to use with my existing hardware, the original model works fine otherwise. Remove white plastic part from the rails, tlip this in instead. Printed from eSun Bone white PLA…
- Downloads
- 3
- Likes
- 2
- Rating
- 0
These are all currently available results.