Counting matching models…
I wanted to build a link dipole for Parks On The Air operations that would be lightweight and easy to put up. I designed these pieces around 22 gauge stranded wire and a bulkhead mount SO-239 connector. Use whatever connector you want on…
Needed a small stick-on holder for my Kenwood ham radio mic in my Ram 1500 pickup. This is attached to the plastic trim of my center console with 3M VHB tape.
I run my Yaesu FT-891 with the front prop up and that aims the speaker up and away from me. I designed this dome to fit over the speaker and push the sound more in my direction. It uses several 6mm x 2mm magnets to secure it to the top of…
Just wanted a way to keep the three calibration keys for my Nanovna antenna analyzer. This holds the small SMA tips very snugly, no glue required. Requires no supports. Print at 0.1mm layer height and inject a color change command just…
My off center fed dipole is 264 feet long and the center piece broke. I designed this to be more robust to allow the connections as well as rope and hardware for hanging in the trees.
I wanted a way to carry my Yaesu FT-891 and its FC-50 antenna tuner as a unit. Pretty simple design. I recommend using M4x10 screws to attach to the radio. Print this on its side with support material under the handle. PETG worked very…
Needed something other than a small flimsy bag to hold the lunar filter for my telescope. The filter I designed this around is 31mm in diameter and 7mm high. I added the text to the top so that I could open it by feel in the dark.
I wanted a way to mount my microphone boom from the vertical column of my monitor stand. The vertical tube is 36mm in diameter so I made this clamp-on holder to fit. You will need two #10 screws and nuts to make this work. I printed this…
My Celestron CPC 9.25" EdgeHD had two of three of these clamps broken. Celestron will send you new ones but it's difficult to get them to work with you. The original clamps are a one piece loop but I didn't want to have to take the legs…
I wanted to position a remote speaker for my ham radio somewhere that I could hear it over the road noise. I found this little speaker and designed a bracket to mount it to my headrest. This fits my RAM 1500 pickup truck. The headrest…
I have coils of coax for ham radio that I need to coil up and keep coiled. I made this little handle and rope mechanism to make that a little easier.
My Celestron binoculars came with a nice bag but one of the clips for the strap broke. I designed this as a replacement with slots so that the strap could slip on and not require removing any stitches. This should work for anything that…
I wanted to lift my large monitor a small amount and create some storage space at the same time. This uses an IKEA Burhult shelf board, but any that match the dimensions would work. Print four of the corners and one of the center…
I have a 53-foot long wire antenna I use for portable ham radio. Used with this unun, it works surprisingly well, but winding it up when I'm done was a pain, so I designed this to mount to the back of the unun. This uses an M8 bolt, nut…
I've seen several FiiO M21 stands but they all had one flaw or another. Mine is sturdy, using a vertical spar underneath to minimize flex. It also has a captive hold on the bottom of the device so it can't slide left or right. And there's…
I wanted to create dividers in my 13" cube storage boxes so I cut some pieces of 4mm corrugated plastic and notched them, but that didn't keep them straight, so I designed this piece to hold them together. Easy print in PLA, no supports…
My Celestron 9.25" CPC's tripod is big and heavy and not the easiest thing to carry around so I designed this handle. It goes together with four M5x16 screws and nuts. This should work on any tripod where the leg is 51mm in diameter.…
I am using the Celestron-brand dew heater ring on my CPC 9.25" telescope but did not want to spend ridiculous $$$ on their heater controller when this $80 dumb controller works just fine. Mounting it to the scope's round barrel when it…
The wheeled cabinet that holds my new printer has 3" casters on it and even when they're locked, the whole cart moves too much when drawers are opened. I designed these to go under the casters to lock it in place. These were designed…
My hamshack is in my unfinished basement and space is limited. I wanted a solution for mounting my microphone arm that wouldn't involve my desk. I came up with this piece which is screwed to the rafter from below and the side with four…
I wanted something that would hold my Fosi Audio DS2 headphone amp in place on my iPhone. This worked out very well. It has a slot that exposes the volume buttons on the side. I used this Magsafe ring on the back. They're adhesive so just…
I wanted a sturdy box to protect my new Fiio M21 DAP. I designed this to hold the DAP while it's in the factory rubber protector. The logo is flush with the top of the lid if your printer supports multi-color printing. If you place the…
If you like my handy carry handle for the Yaesu FT-891/FC-50 combo, you might like this add-on plate that can hold an Ethernet coupler so you can quick-change between your hand mic and a headset. I used these short Ethernet cables and one…
My speakers are on top of shelves, and I noticed the bass got better if I got them a little closer to the ceiling, so I designed this stand to give me the lift I needed. These are 190mm square and 125mm tall. Print both with the large…
I really liked @blablabliam's Orion Starblast solar filter and wanted a good way to store it. This is a simple box with a friction fit lid. There are holes in the bottom to let it breathe when you close it. There's some clearance around…
These are all currently available results.
