P
PrintablesB3dprint
oak and maple leaf cookie cutter
oak and maple leaf cookie cutter
- Downloads
- 1,368
- Likes
- 142
- Rating
- 4.83
All models
Counting matching models…
P
PrintablesB3dprint
quick print scraper
Depending on print height, it will print in 25(0.28) to 48(0.16) minutes. Smaller print heights will be sharper. feel free to make it thinner to print even faster
- Downloads
- 670
- Likes
- 29
- Rating
- 4.71
P
PrintablesB3dprint
All 50 US states and Puerto Rico
Individual STL and SVG for each state and Puerto Rico
- Downloads
- 294
- Likes
- 21
- Rating
- 0
P
PrintablesB3dprint
Calibration cube
a 20mm X 20mm X 20mm cube with embezzled text for calibration of distances takes 20min to print with 10% infill and 2 walls 2 top and bottom layers and uses 3g of filament
- Downloads
- 253
- Likes
- 2
- Rating
- 5
P
PrintablesB3dprint
Gojo NAH I'D WIN
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm Filaments Used: PLA Elegoo Black Transmission Distance: 1.8 PLA Elegoo White Transmission Distance: 9.4 Swap Instructions: Start with Black At layer #3…
- Downloads
- 248
- Likes
- 10
- Rating
- 0
P
PrintablesB3dprint
dragon wall sconce
As this is a scan that I made and cleaned up, there are a few places that will lode unnecessary supports on the chin feel free to remove but I printed with them it does not add too much filament.
- Downloads
- 226
- Likes
- 71
- Rating
- 0
P
PrintablesB3dprint
real snowflakes ornament
snowflakes ornament based on a real snowflake
- Downloads
- 189
- Likes
- 26
- Rating
- 0
P
PrintablesB3dprint
hand sanding block
hand sanding block printed in pla but can be printed in tpu use at leas 2 perimeters and 15% fill. Print on either side so you don't need support. (supports should be on for the inlay)
- Downloads
- 119
- Likes
- 22
- Rating
- 5
P
PrintablesB3dprint
book mark
There are two, a thin two-layered version (0.4mm) and a thick four-layer version (0.8mm). I use the words to tell if I left off on the right or left page. They take 22 or 44 minutes to print at 0.2mm using a 0.4 mm nozzle
- Downloads
- 67
- Likes
- 4
- Rating
- 0
P
PrintablesB3dprint
PAL autosampler tray
made this tray to fit a water isotope autosampler. The bottom is the original tray top is printed. Printing: PLA 10% infill 205 C nozzle 50 C bed 0.4mm nozzle 0.2mm layer height 3 layer top, bottom, walls 50 mm/s print speed 25 mm/s outer…
- Downloads
- 46
- Likes
- 3
- Rating
- 0
P
PrintablesB3dprint
Marro Heroscape
This is a Marro Drudge from Heroscape. There are a few versions added they are all very similar however some have been post-processed a little. prints well on FDM Ender 3 finer layers are better. Print Settings Printer Brand: Creality…
- Downloads
- 41
- Likes
- 10
- Rating
- 0
P
PrintablesB3dprint
Replacement Royal typewriter rollers
These are replacement rollers for a 1928 Royal Model P Typewriter. Included are the top rollers and both sets of bottom rollers. The bottom rollers are covered in 3/8in heat-shrink tubing. The rollers need replacing when they are worn…
- Downloads
- 39
- Likes
- 11
- Rating
- 0
P
PrintablesB3dprint
marble levels
This is a set of three levels you will need to print each of them on their side so that they work best only the 360 level needs support. The center gage should be facing up, the disk can be printed on its flat side or edge, but the edge…
- Downloads
- 37
- Likes
- 45
- Rating
- 5
P
PrintablesB3dprint
Ban seven deadly sins Hueforge
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm Filaments Used: PLA Elegoo Black Transmission Distance: 0.3 PLA Elegoo Red Transmission Distance: 4.5 PLA Elegoo Gray Transmission Distance: 5 PLA Elegoo White…
- Downloads
- 25
- Likes
- 6
- Rating
- 0
P
PrintablesB3dprint
Soil coaster CT scan
This is a section of a CT scan performed on an agricultural soil using ImageJ software
- Downloads
- 20
- Likes
- 2
- Rating
- 0
P
PrintablesB3dprint
hangable soap caddy
a holder for your soap that has a rope and drain holes
- Downloads
- 9
- Likes
- 0
- Rating
- 0
P
PrintablesB3dprint
Core one extender for dry box and solid state dehumidifier
This is an extender for the Coer One Drybox with a solid-state dehumidifier addition. This allows the original spool holder to be used and, therefore, allows larger spools. Additionally, the RS2 solid-state dehumidifier (…
- Downloads
- 2
- Likes
- 0
- Rating
- 0
These are all currently available results.