Counting matching models…
A little less boxy style pen/pencil holder to attach to your IKEA Skadis pegboard. Comes in 3 version with 2 and 3 dividers. Requires glue or 3DGloop to attach the ‘peg hooks’ to the back. Print without any supports or brim.
Design to hold the very large Ryobi 40 volt batteries on a wall panel. Large screw hole and thick base to lift it off the wall enough to be easily accessible. Printed in PETG.
Created this wall bracket to hold my iPhone 11 Pro near me while in my recliner since there was no actual table or shelf nearby. Fits phones that are 144.00 x 71.40 x 8.10mm with some extra space on the sides for wiggle room. Round hole…
microRACK was designed to solve a problem of building a homelab in limited space with maximum versatility. It's follows standard rack spacing with each module being 1U (approx. 44mm). The modules are fastened to the track using standard…
Custom container and staking tray for the upper centre section of the Husky 22 in. W 22-Compartment Connect Cantilever Small Parts Organizer. This one -…
I designed this case that's inspired by visual futurist artist like Syd Mead and John Eaves. Not your typical boxy type case for a piece of audiophile equipment. This is meant to make it standalone and have a visual impact with futuristic…
I'm designing a SKAID panel to hold all my batteries, flashlights, battery chargers and walkie talkies. These are 4 of the battery pack holders I've designed and printed. Friction fit for the packs and as low profile as I could make them.…
Custom slot loaded (top down friction fit) for the Zimablade SBC module for use in the microRACK homelab setup. This has an additional slot for mounting a SSD or 2.5" hard drive. REQUIRED: You will need to print the microRACK track to…
Custom slot loaded (top down friction fit) for the Zimablade SBC module for use in the microRACK homelab setup. The module has 2 VERSIONS depending on which ports you want accessible on the front. REQUIRED: You will need to print the…
Needed to reclaim some desk space so I made this bracket that screws into the wood drawer of the IKEA Elloven monitor stand. Added extra slots on the lower part so you can hear the speakers and opening to be able to charge and insert into…
Another design by @DEEPSPACEDIVES More to come at https://www.instagram.com/deepspacedives This is part of a growing collection of 1:6 scale accessories I'm designing for my Iron Man, Tony Stark figure displays. This is suitable for any…
Custom module (slot loading) to hold a Raspberry Pi4 inside an Argon One case with the M.2 extension this module for use in the microRACK homelab setup. The module has 2 VERSIONS depending on which ports you want accessible on the front.…
Holder for NB-2LH Canon camera batteries. Comes in a 2x, 3x and 4x versions. Print without supports.
This design will hold the 8-Port GIGABIT version from D-Link. Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: No Supports: Yes Infill: 30 Filament: Anycubic PLA White Category: Organization
Custom slot loaded (back to front) for 2.5 inch HHD or SSD for use in the microRACK homelab setup. REQUIRED: You will need to print the microRACK track to mount this module. Printing in PETG is recommended.
Custom slot loaded (rear loading) for the EdgeRouter X Switch module for use in the microRACK homelab setup. This has an additional slot for mounting a SSD or 2.5" hard drive. This is modelled based off of specification dimensions, so I…
Custom slot loaded ESP32 holders that slide into a track module designed to hold 4, 6 and 8 ESP32s. This module is for use with the microRACK homelab setup . This was designed ot experiment with Nerdminer however it's intended for any…
These are all currently available results.
