Counting matching models…
Update (2025-01-26): Added new models for easier clamping. AT XXmm Casting Tube To Base Holder files are used to hold the casting tube to the base with fewer clamps. Take a look at the pictures to see how I use it. I use these to cast…
Avionics sled that will fit in 3+ inch airframe tubes. Common to both sleds: Rotary switch - https://www.digikey.com/en/products/detail/schurter-inc/0033-4501/641120?s=N4IgTCBcDaIMoGMAWBXATgFwKZoAQAZ8BmIgOgBYBWfARhAF0BfIA Altus Metrum…
Avionics sled that will fit in 3+ inch airframe tubes. Rotary switch - https://www.digikey.com/en/products/detail/schurter-inc/0033-4501/641120?s=N4IgTCBcDaIMoGMAWBXATgFwKZoAQAZ8BmIgOgBYBWfARhAF0BfIA Altus Metrum EasyMini x2-…
4-inch LOC Precision Avionics Bay Bulkhead. I design my parts to be replaceable as much as I can. So, nothing is glued on my AV bays. I use lock nuts and lock washers instead. Components I use: 4-40 threaded rods for the e-match terminals…
Avionics Bay Black Powder Well/Canister. A 4-40 screw will fit in the hole at the bottom of the charge well. Can be printed with just about anything. I've used PLA and PETG. Small can hold slightly more than 2 grams when using an e-match.…
Avionics sled that will fit in 38+mm airframe tubes. Included adapter is needed for 3+ inch diameter rockets. Rotary switch -…
This system allows you to use the same pieces over and over. No need for multiple cartridges. You will need some lead shot or anything that fits inside the compartments and has weight. I use lead shot in Ziploc bags as seen in the photos.…
Avionics Bay Terminal Threaded Nut for 4-40 threaded rods. Works best if you use a 4-40 tap on the nut. I use these to make sure my 4-40 threaded rods (used as a terminal) can't be shorted out. The little nubs on the nut, help pull in the…
3-inch LOC Precision Avionics Bay Bulkhead. I design my parts to be replaceable as much as I can. So, nothing is glued on my AV bays. I use lock nuts and lock washers instead. Components I use: 4-40 threaded rods for the e-match terminals…
4-inch Fiberglass/Carbon Fiber Avionics Bay Bulkhead. I design my parts to be replaceable as much as I can. So, nothing is glued on my AV bays. I use lock nuts and lock washers instead. Components I use: 4-40 threaded rods for the e-match…
4-inch Madcow Avionics Bay Bulkhead. AV Bay for Quantum Tubing. I design my parts to be replaceable as much as I can. So, nothing is glued on my AV bays. I use lock nuts and lock washers instead. Components I use: 4-40 threaded rods for…
5.5-inch LOC Precision Avionics Bay Bulkhead. I design my parts to be replaceable as much as I can. So, nothing is glued on my AV bays. I use lock nuts and lock washers instead. Components I use: 4-40 threaded rods for the e-match…
Used to adapt the shaft of a 5/16" square shaft to 1.25" PVC pipe. Slides onto the PVC pipe and should be friction fit. If not, add tape or something to make it so.
7.6-inch LOC Precision Avionics Bay Bulkhead. I design my parts to be replaceable as much as I can. So, nothing is glued on my AV bays. I use lock nuts and lock washers instead. Components I use: 4-40 threaded rods for the e-match…
This case + cap for TeleGPS is designed for being in a 38mm+ body tube with a 400mah LIPO battery. It also allows for plugging into the USB port without having to take anything apart. The cap must be used with the case. The cap helps hold…
Update: Added Top Cap to protect the antenna. Pictures show the long bottom/top caps in use. This case for TeleGPS I designed for being in just about any rocket. It will fit in a 38mm body tube. You may need to shave the corners a little…
These are all currently available results.
