Counting matching models…
Reformed the clamp, so it closes all the way and also deforms the cable to be able to also clamp very thin wires. The base must be printed together with the clamps (print in place). The single files of the base and the clamps are only for…
The tool deliverd with my Seat Alhambra was crap. Therefore I designed my own, which works lika a charm. Category: Hand Tools
Inspired by https://cults3d.com/en/3d-model/home/universal-drink-markers-work-for-stemmed-or-stemless-glasses-mugs-and-cans-12 I created my own version with icons from openmoji.org If you want to use other icons, store them as svg, locate…
I had problems with the model available ( https://www.thingiverse.com/thing:5151297 ). The tokens fell off between the gears. Therefore I created my own version without rounded edges. I tried to get the numbers as round as possible, like…
Lid printed in TPU for 95mm Yoghurt. May also work if printed in PLA. If you need another diameter you may adapt the OpenSCAD file Category: Kitchen & Dining
This holds highlighter markers and doesn't use a counterweight. The tray on the front can be used to put a rubber or other things on it. Very nice to pick up the highlighter and to put it back. Variations are available for 2 to 6 markers,…
This is a holder for highlighter markers. I added models for 1 to 6 markers. On the backside there is a hole to put an M12 threaded rod as counterweight. It's nice and holds my Stabilo Boss best. Category: Office
If you don't want the strainer of your bodum tea pot, you can just print one of this. Because the original lid just sits on the stainer, it is not possible to use it without the stainer. This Lid sits directly on the pot itself. So you…
Needed to connected two rods with 19mm and 14mm diameters 30mm appart. Therefore I remixed the design and added this variant. Category: Tools
A very comfortable glasses frame designed to hold magnifying lenses from inexpensive magnifying glasses. The original Parkside magnifying glasses are quite heavy because they include a built-in LED light and batteries. As a result, they…
Used the design from @stanoba and adapted it to have space for 15mm thick tapes. Also widened the the open window so it matches for our usage on our manual PnP machine Powatec Expert II . Added a baseplate which slides on the base plate…
A simple separater for a lunch box that does not have one. It consists of a base on the bottom and a separator shield. It separates fairly firm Print Settings Printer: RepRap Mendel Rafts: No Supports: No Resolution: 0.2 Infill: 40%…
This is a improovement of the simple Car Fob Protection Filled . The simple cover broke often at the key ring. So I designed a whole case. It is sturdy enough to prevent unwanted opening of the car and windows, but it is soft enough, so…
This is a holder for my controller of the headset to hang on my little table drawer. Print on its side for best strength. Have to use support for the front latch of the other side. I added version 2 with thicker walls and event thicker…
This reduced the slot width of the 8.5mm slots of the Screwdriver holder by dodasch ( https://www.printables.com/model/102242-screwdriver-holder-wall-mount ). Like this the smaller screwdrivers with smaller shafts don't tilt that easily…
This device is just a simple RGB-LED with a display which can be controlled by the virtual serial port on its USB connection. In combination with the appropriate desktop application Lync-Presence-Bridge it shows the active Lync / Skype…
This is a gimmick to illustrate the TZI-Model. If one of the gactors weights more, the model will be out of balance. It is required to have all factors balanced, and so also the model is balanced. This is based on the theory of Ruth Cohn:…
I designed this holder to store the mini hot plate MPH30 of Miniware, which can be purchased from Digikey under FIT0888. Category: Organization
These are all currently available results.
