P
Printablesswitchboard.op
Moth Antennae Headband
These are designed to slip onto a thin metal headband. Printed in PLA at 100% infill with print thin walls enabled.
- Downloads
- 943
- Likes
- 190
- Rating
- 4.33
All models
Counting matching models…
P
Printablesswitchboard.op
Pen Plotter Mount Remix for Sprite Extruder
I found that the mount by Fizzy Chickens needed a little more material around the back of the screw hole. The bolt that came with my printer was bottoming out so I added a small collar around the hole too. Deleted the extra bit opposite…
- Downloads
- 125
- Likes
- 14
- Rating
- 5
P
Printablesswitchboard.op
SLC Carrier Wall Storage (SW-Motech)
Print two normal and one locking pin per bag. Use the template to figure out where to mount them with countersunk screws. I printed all parts in PLA+ with 100% infill. So far they are holding up. Thanks to @Robin for the pins and spacing.
- Downloads
- 29
- Likes
- 4
- Rating
- 0
P
Printablesswitchboard.op
Pocket Operator Display Stand 6U
A simple stand to hold six Operators vertically for display. Fits POs with the OEM case. v1 tilts them back 5° and is 20mm tall. v2 keeps them completely vertical and is 12mm tall. Pictures are of v1.
- Downloads
- 28
- Likes
- 9
- Rating
- 0
P
Printablesswitchboard.op
SW-MOTECH Pro Tank Bag Wall Spacer
20mm spacer for wall mounting SW Motech Pro tank bags with a recess like the Pro City. I have not printed or tried this yet but I plan to update when I do.
- Downloads
- 26
- Likes
- 1
- Rating
- 0
P
Printablesswitchboard.op
Pocket Operator Display Stand 1U
A simple stand to hold a Pocket Operators vertically for display. Fits POs with the OEM case quite snugly. Prototype for a larger stand: https://www.printables.com/model/368542
- Downloads
- 24
- Likes
- 1
- Rating
- 0
P
Printablesswitchboard.op
Pocket Operator Display Stand 3U
A simple stand to hold three of your Pocket Operators vertically for display. Fits POs with the OEM case quite snugly. Prototype for a larger stand: https://www.printables.com/model/368542
- Downloads
- 20
- Likes
- 3
- Rating
- 0
P
Printablesswitchboard.op
Ableton Push 1 Upright Stand
Remix of a stand for the Push 2 by agurzil to work with Push 1 Holds the Push in an upright position for display. Can also be used to prop it up in a more ergonomic position while playing. Mirror the model for the right side. Printed in…
- Downloads
- 19
- Likes
- 0
- Rating
- 0
P
Printablesswitchboard.op
Yet Another Patch Cable Hanger (6U remix)
A smaller version of the patch cable hanger by Brad Brok This one has six slots. Printed in PLA 10% infill, three walls, no supports.
- Downloads
- 17
- Likes
- 0
- Rating
- 0
P
Printablesswitchboard.op
Foldable TCG Sorting Tray Cover (perfect fit)
The fordable card sorter is great, but the cover in the original model was too large. I took 10mm out. I printed with 0% infill, no support in PLA.
- Downloads
- 17
- Likes
- 8
- Rating
- 5
P
Printablesswitchboard.op
Simplehuman Step Can Wall Spacer
My trashcan kept sliding against the wall when i would step on the foot switch to open the lid. It Scuffed the wall over time. This spacer holds it away from the wall with enough clearance for the lid. Designed this for a Simplehuman 30L…
- Downloads
- 6
- Likes
- 1
- Rating
- 0
These are all currently available results.