Counting matching models…
A simple GoPro mount I made to better (more securely) fit the profile of my M/L Sweet Protection Strutter. Most likely usable for other helmets (duh) but make sure you have tethers and such, as I'm not responsible for your camera. I…
Acquired a pair of OEM "Upgrade" speakers from a ~2010 Impreza, but the brackets needed for the front doors of my Forester of the same year are quite different. Adapted the previous model's size to fit the ~5 1/2" speaker, and added holes…
Correct dimensions for a Jackson whitewater kayak drain plug prior to 2015-ish when they changed plugs. Yopsolo's plug fits, but is about 3mm too long to bottom out correctly on my kayak. Shortened the threaded portion, filled the center…
Relatively basic adapter to mount newer LED fog lamps to the factory locations in SH Foresters 09-13. I used a pair of washers and a flange nut to act as a spacer between the back of the adapter and the vehicle side mount to set the…
Had a Campy Super Record front mech with a broken lower brace, so I modeled a new one. Seems to fit pretty darn well, needs a little adhesive around the carbon tab just like the original. Printed first with ASA, but might actually be best…
Simple low profile crank boot for GRX cranks modeled from an 810/820 crank arm, Print in TPU with support. Fit mine quite well, may get the best results if fitted while warm. Edit* Drive side arm has a different profile, working on a new…
Broke both my fork lockout levers with my knee in a crash. These aren't perfect, but will do the job. The hole on the lower lever is meant for you to drive a 2mm screw into it and remove the head - easiest way to get a strong 2mm post. I…
Chainstay protector for Giant Revolt - mine is a size Small, and it fit perfectly. Printed with TPU standing on end, with a brim, turned down speed near top 3rd. May the odds ever be in your favor. Category: Sport & Outdoors
Altered the design to use m3 heat set inserts. Category: 3D Printer Parts
As the name says. The dimensions weren't 100% perfect to the original, but they actually seemed to fit better on the fork I tested them on. Meant to be resin printed, but could be printed via FDM if turned on the side. Bolt is an M3 cap…
A simple thumb nut 1/4-20 to fit the seat stud of my Jackson Kayak. If I get ambitious I might create a model to use threaded inserts later. Let the stud clean up the plastic threads, it will be a little snug. Category: Sport & Outdoors
Fits some Stihl saw cases, made to print somewhat easily and be "super good enough". Not a perfect 1:1 recreation - I lack the Skil for that Print in PETG at 100% with normal supports. Category: Parts
Axle vice for QR wheels, print with thick walls/infill as there will be a lot of force applied to them. Hole size might be a touch small out of the gate, but should be workable in a pinch. This isn't meant for heavy use, I just needed it…
Made some models for some of the plastic breakable bits on the Giant Crest forks after seeing a few broken caps. I printed mine out of Elegoo WW space grey resin and the fit was finer than the OEM parts. The threads in the cap are 5/16…
Simple fork mount for a 12x100 thru axel to mount on the center headrest of a ~2010 Subaru Forester or similar. (10mm headrest posts 95mm spacing) **Update: loosened tolerance a little on the headrest portion. Apparently 40+ people…
A simple replacement (mostly temporary) thumb screw/nut Loosely based on the Pyranha Foot Rest thumb nut (M6x1.0) May fit other models, let the bolt threads clean up the plastic threads. If I get ambitious enough later, I might create a…
Small bumper for the liftgate of a 2010 Subaru Forester. Meant to be printed in TPU, print on the heavier side, but 100% doesn't seem to be warranted. 6 walls and 20% seems adequate. YMMV. May fit other models, I haven't checked. Edit: V2…
Frame protector for the Giant Revolt near the BB. Printed mine in TPU with 20% gyroid 3 walls, tops, and bottoms Category: Sport & Outdoors
Designed a holder for credit cards, parking passes, ID's and what not to make driving solo easier. I use 3m outdoor extreme double sided tape on the block to place it. The holes in the main body are sized to insert m3 heat set inserts…
Print the main body on end, and the tab on its side for best results. Use M3 heatset inserts in the body, and countersunk screws to secure the tab. I prefer ASA but PETG would likely serve well. I printed at 100% infill Category: Sport &…
Haven't printed this just yet. Rough model based on a fork that was missing the cover. This model is for the Giant Animators, and Liv Adores with the plastic forks. No clue if it fits any other models. If you wanted, you could probably…
This replaces the insert for the center stem mount from Lezyne. The three holes are spaced at 10mm, and there is one version for using brass inserts (M3) and one to thread directly into the part. This should allow you to screw a GPS mount…
Replacement/repair post for the blade guard on a Dewalt miter saw. May fit others, meant to use an M3 heatset insert and a countersunk screw. PLACE THE INSERT WITH THE POST IN PLACE ! The material flow from placing the insert will help…
Haven't printed this just yet. Rough model based on a fork that was missing the cover. This model is for the Giant Animators, and Liv Adores with the plastic forks. No clue if it fits any other models. If you wanted, you could probably…
These are all currently available results.
