Counting matching models…
This is part two of a remix of 2 voron mods: the 2.2 Z-belt covers with hidden cable routing and the matching cover inserts. Its purpose is to keep as much heat inside the chamber as possible by shrinking the opening for the Z-belt in the…
This is part one of a remix of 2 voron mods: the 2.2 Z-belt covers with hidden cable routing and the matching cover inserts. Its purpose is to keep as much heat inside the chamber as possible by shrinking the opening for the Z-belt in the…
Onshape link: https://cad.onshape.com/documents/85f8af9c3560631ef3a8b8bd/w/b93b61fa09455d7486abba95/e/4e7766a88ce26446d93daaf5?renderMode=0&uiState=68b9db116f2d604265e6ce23
This is a cover for the Eachine PRO58 diversity module. The module goes into the cover, then the cover into the goggles. It has clips which will prevent it from falling out of your fatsharks while you fly. No tape needed! I designed this…
This is a shroud for an XT-60 socket which should fit into the hole in the case of a typical ATX power supply to replace the mess of wires with a single connector for the voltage you need out of the supply. I tested it with this…
This is a simple tool for holding the bell of a brushless motor to prevent it from rotating while installing or removing propellers. It's printed in 2 parts. The main body can be printed with PLA, although it would probably be more…
A connector between 2 parts of the broom. Thread on one side, a snug fit socket on the other. The onshape model is parametric and must be customized for your broom. The attached STL is just what works for mine. Print with 100% infill, 3…
I made this simple XT60-cap organizer to help not loose the caps while flying. It is best to print it using TPU. It has a slot through the middle that allows to bend it to more easily remove the caps. Thanks to this it could be made as…
Print at 0.1 layer height for best quality. 15% should be enough for the holds. Use 100% for the pins. Use M2 socket head bolts: 12mm, 12mm, 8-10mm, 6-8mm, 6-8mm for holds number 1, 2, 3, 4, 5 respectively. Use the longer ones if you're…
Ever had 2 cream tubes, one full, the other almost empty? And you need one at work and one at home? Guess what, now you don't have to buy the third one just yet! Transfer half of the full one to the empty one! This simple inner thread…
A simple 60% keyboard keyboard dust cover designed specifically with the Tofu60 2.0 in mind (asymmetrical top and bottom lips). There's enough space inside to fit 1mm strips of foam for better protection.
A rail that goes between 2 drawers of Standing desk drawer to minimize the space between the 2 drawers.
Designed for the Blitzwolf BW-WA4 portable speaker which I use as a soundbar, so that it is more angled and the high frequencies can reach the ears better;). You can use the onshape model to adjust the dimensions to your speaker and…
A Topre switch spring tray to prevent the springs from tangling up while you're modding your keyboard.
A cap for the kingrinder P2 coffee grinder to store it with the handle hanging down.
You can use 2 of those (hole version) to get a cable out of a 45mm mosaic socket.
This is a simple hack which allows you to connect an XT60 battery to the fatshark dominator goggle family without voiding your warrany. You'll need: an Amass XT60H male connector, a 2S balancer plug, a 5.5mm DC jack plug, the printed…
If you are using silencing rings mod on your Realforce 87U, the whole action is moved down a little. At about 0.5mm thickness of the rings, some keys (especially the longer ones, like enter or shift) may begin to touch the plate when…
This is a simple lightbar with tilt regulation that goes on the back of the monitor to light up the wall behind it. The 2 rods (part a and part b) are connected with a 20mm m3 bolt and a hex nut. The LED strip is mounted with double sided…
A base on which to put your air humidifier so that it blows the fog right at you!
A simple enclosure for the Nettigo Air Monitor 0.3.3 particle sensor. Onshape link:…
Dodatki do półki drucianej INTEGRI ( https://domax.com/pl/model/arwa?tab=browse ) Haczyki najlepiej się sprawdzają drukowane z nylonu PA12, infill 100%, co daje dobry kompromis między wytrzymałością na obciążanie a sprężystością potrzebną…
These are all currently available results.
