Counting matching models…
This is a generic removable tripod mount. This measures at 43.5mm squared. This is to replace or in addition to a stock removable mount with use of a 1/4in screw + washer. This has been tested on a Merkury Innovations tripod. The irony of…
I was liking the layout of thing:3661633, but needed thing:1284641. I did not feel comfortable printing thing:1284641 out standing up, or even on its side with supports. Since I wanted the most strength, I decided to mix them, in a way.…
Some friends were doing an Alien themed party and wanted to use https://www.thingiverse.com/thing:1057666 , but I didn't want to print it all as one. I also like flipping these kinds of models on their back to keep support gunk hidden. So…
I wanted a basic cover to put over my batteries when not in use as I do not like to store them in the tool. Made in openscad. Tried to over engineer it and ended up going back to some basics. This should fit the battery snugly, but not be…
Wanted to make my own take on the amiibo stands, this one you can print out a single stand, or multiple and interlock them together. Base is a bit thin where the figure sits, but it should be sufficient enough. If anyone needs it…
EDIT 2022/06/21: Uploaded version 2.3! I modified the last knob to now have little grips on the outside of it. This makes it easier to spin the knob with a flick of a finger. EDIT 2020/06/17: Uploaded version 2! I recently lost the…
Customized version of http://www.thingiverse.com/thing:1329750 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing\_id=1329750 Print instructions Category: 3D Printer Parts Instructions Using the following…
I was being lazy and did not want to go into my attic during the summer heat to pop a hole for a ceiling mounted AP. So I made this to hang off of one of the common RubberMaid shelf units until it gets colder. This is a bit tight, but it…
I recently purchased some POM nuts from RobotDigg, but noticed they only had 3 mounting holes. Since I am running a custom MK2 clone, I wanted something close to the original with little modification, Enter the new x ends. This is a…
Not liking the endstop holders I've seen online, I went for something simple and functional. This fits a KW11-3Z micro switch and all it needs is a zip-tie, M3 screw and nut. Pictured is a M3-25 screw. This fits nicely on a QUBD OneUp and…
NOTE: I am still working on the RAMPS 1.4 config file with Marlin 1.1.0. Currently the printer does move around and extrude slowly, but not print worthy just yet. Testing parts to upgrade my 101hero from its gear reduction steppers to…
I had some older HP servers at work with Ni-MH batteries that kept bulging, and reporting as failed. Anyone in this circumstance knows that if you order a new battery, you are either getting a seller refurbished (aka they didn't do…
Updated and added version 1.1, which drops the height of the spacing between the stepper to the endstop by 2mm to fit better. This change also makes it compatible (checked!) with the TwoUp! Doing the 'make my own thing' for the X endstop…
I have been playing around with this x230 frame from HobbyKing and it has one major flaw, it has no legs. This will cause a problem, as the quad will routinely tip over and break the props. Maybe an experienced pilot will not have this…
I wanted to add an additional tag to my cats collar with a link to her pictures (In case collar is removed) and contact methods to reach me. This tag is 24x18x2mm, plus a small loop on top for the collar. It was designed to fit around the…
Got tired of having my wire wrap hang free... Then got tired of having my wire wrap taped to my frame. Made this simple holder to clip onto the right (or left!) side of the QUBD One/TwoUp frame so I can cable tie the wrap down. This…
These are all currently available results.
![Simple X-Axis Endstop holder for QUBD OneUp and TwoUp [Updated]](https://media.printables.com/media/prints/12715/images/113160_5115d957-3bc2-481a-83a7-ff4743205239/img_20140810_152829_12715.jpg)
