P
PrintablesJudah Chang
chair
when i first started 3d modeling i made a chair as practice. want it? Category: Props
- Downloads
- 1,444
- Likes
- 31
- Rating
- 5
All models
Counting matching models…
P
PrintablesJudah Chang
weighted d20
A weighted 20 sided die. i designed it so that you can roll high numbers or low numbers, depending on the die.after i just used a fine tip sharpie to colour in the numbers. Print Settings Printer: Anycubic Rafts: No Supports: Doesn't…
- Downloads
- 450
- Likes
- 23
- Rating
- 4.5
P
PrintablesJudah Chang
mini sunglasses
a mini pair of sunglasses for whatever you want. the pair on the duck was resized up to about 125% so the original model is a bit smaller. Category: Models
- Downloads
- 319
- Likes
- 13
- Rating
- 5
P
PrintablesJudah Chang
bouldering holds
Some rock climbing holds I designed for my climbing wall. I designed them to be fastened to the wall with a 3/8 lag bolt but it should work with the standard allen bolt also. I printed these with a .8mm nozzle at a .3mm layer height. The…
- Downloads
- 211
- Likes
- 28
- Rating
- 5
P
PrintablesJudah Chang
grippy chopsticks
grippy chopsticks. one right handed chopstick file and one left handed chopstick file ;). i printed them laying down cause i though that would be the strongest but you can do whatever you like Print Settings Printer: anycubic Rafts: No…
- Downloads
- 203
- Likes
- 14
- Rating
- 0
P
PrintablesJudah Chang
cardboard screws
screws made for screwing together cardboard. Can be printed without supports Category: Construction Toys
- Downloads
- 143
- Likes
- 36
- Rating
- 5
P
PrintablesJudah Chang
uke dino capo
a capo for a ukelele that is shaped like a t-rex skull. Print Settings Printer: anycubic Rafts: No Supports: Yes Resolution: .1 - .2 Infill: 100 Filament: polymaker pla white Notes: you will have to print support for the inside of hole…
- Downloads
- 127
- Likes
- 33
- Rating
- 5
P
PrintablesJudah Chang
pythagorus mug
A remix of the pythagorean cup by pythagorus. is functional albeit a bit slow. when printing with supports you have to make sure that it doesnt generate supports inside the handle. this will block the flow of the water coming out. to do…
- Downloads
- 116
- Likes
- 8
- Rating
- 5
P
PrintablesJudah Chang
uke capo
a capo for a uke. duh. the capo part should have a bit of support to hold up the threads. it will take a little working to get it to spin smoothly. Print Settings Printer: Anycubic Rafts: No Supports: Yes Resolution: .1mm Infill: 100%…
- Downloads
- 86
- Likes
- 6
- Rating
- 0
P
PrintablesJudah Chang
uke holder
A holder for most regular ukeleles. i just used a command strip to hold it and its been good so far. i was trying to go for an easy print this time. this can also probably be scaled up to hold a guitar if you want. i havn't tried this yet…
- Downloads
- 76
- Likes
- 8
- Rating
- 5
P
PrintablesJudah Chang
life size strong printable katana
a katana that i section into pieces so that it would fit on a 3d printer bed. only one of every piece is needed exept for the key. that will need to be printed twice. the peices should all fit together but will need to be glued to stay…
- Downloads
- 57
- Likes
- 7
- Rating
- 0
P
PrintablesJudah Chang
freedom convoy jerry can
i wanted to make a jerry can keychain for the freedom convoy will have to print support for the nozzle but the rest is fine Print Settings Printer: Anycubic Rafts: No Supports: Yes Resolution: 1.3mm Infill: 25% Filament: garbage pla red…
- Downloads
- 34
- Likes
- 7
- Rating
- 0
These are all currently available results.