P
PrintablesJim.Lee
40gram washing powder spoon
40 gram washing powder spoon or 41ml normal washing liquid
- Downloads
- 250
- Likes
- 11
- Rating
- 4.75
All models
Counting matching models…
P
PrintablesJim.Lee
Macbook pro wall mount
a simple mount for macbook pro or any other slim laptops. Uses 2x wood screws each.
- Downloads
- 217
- Likes
- 25
- Rating
- 4.5
P
PrintablesJim.Lee
Two-level Foil/Wrap holders
doesn't really need it to be three-layered,so i edited the original to two-layer holder.May save u a little hassle. Print instructions Category: Kitchen & Dining Summary doesn't really need it to be three-layered,so i edited the original…
- Downloads
- 152
- Likes
- 41
- Rating
- 0
P
PrintablesJim.Lee
Ratrig V-minion SKR e3 mini / ender3 style motherboard electronic enclosure
I have to give the model 10mm offset from Y axis extrusion to clear the enclosure from Y end-stop&y motor. The controller board will be installed upside-down and having the hot end&heated bed connectors facing Z motor direction. All 4.5mm…
- Downloads
- 81
- Likes
- 8
- Rating
- 0
P
PrintablesJim.Lee
nitendo switch game card shelfholder
nitendo switch game card shelfholder
- Downloads
- 78
- Likes
- 13
- Rating
- 0
P
PrintablesJim.Lee
esp01s ws2812 wireless led ring enclosure
Parts used: 1x ws2812 led ring with 24 units 1x esp01s 1x ws2812 esp01s to ws2812 adaptor unit Firmware: ESPHOME Configure the led ring with neopixelbus Here is an example that works:(Only the light section of esphome configuration file)…
- Downloads
- 71
- Likes
- 25
- Rating
- 0
P
PrintablesJim.Lee
Clash of Clans Inferno Tower Single Color Printable
Inferno Tower for single color printers. Better print center parts with 97% - 98% scaling or it might not fit. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Resolution: 0.2mm Infill: 0-15% Filament: eSUN PLA+…
- Downloads
- 56
- Likes
- 16
- Rating
- 0
P
PrintablesJim.Lee
dell soundbar mount general purpose
Feel free to remix it as it's just a mounting part. You can: 1.print this,use some super glue to stick your stuff with the mount part and attach to the monitor 2.design your remix using this as a mounting part Print instructions Category:…
- Downloads
- 53
- Likes
- 6
- Rating
- 0
P
PrintablesJim.Lee
Mac Mini M4 Mount With Dust Shield
Added dust shield and bottom air intake/exhaustion divider.
- Downloads
- 44
- Likes
- 8
- Rating
- 0
P
PrintablesJim.Lee
Trash Bag Dispenser (Two Rolls)
Maximum outer diameter of a bag roll is 70mm. The heatinsert on mounting plates are m3 inserts with the length of 4mm and outer diameter of 5mm. I'm using four m3 x6 screws between mounting plate and the dispenser body. Contact between…
- Downloads
- 36
- Likes
- 11
- Rating
- 0
P
PrintablesJim.Lee
Cetus MK2 PLUS
Big thanks to Gio Van's Cetus 3D printer ,so that I wouldn't need to start from scratch. Test run videos: (Vs prusa mini)[ https://www.youtube.com/watch?v=mT3fT1IKzkA ] (Voron test cube)[ https://www.youtube.com/watch?v=NwDWOP7rJes ]…
- Downloads
- 36
- Likes
- 5
- Rating
- 0
P
PrintablesJim.Lee
EKEN H9R Replacement Case
A not so simple replacement case for some dirt cheap chinese 4K sport cameras that did't come with cases. Print with tree support if u need any. Print instructions Category: Electronics Summary A not so simple replacement case for some…
- Downloads
- 29
- Likes
- 4
- Rating
- 0
P
PrintablesJim.Lee
IKEA enclosure ventilation mount with cutoff holes
IKEA enclosure ventilation mount with cutoff holes for IKEA plasta storage system.
- Downloads
- 15
- Likes
- 5
- Rating
- 0
P
PrintablesJim.Lee
replacement casing for netgear r6900 router
replacement casing for netgear r6900 router
- Downloads
- 8
- Likes
- 0
- Rating
- 0
P
PrintablesJim.Lee
160mm wall-vent cover/cap
160mm wall-vent cover/cap Glue two parts together once printed.
- Downloads
- 7
- Likes
- 2
- Rating
- 0
These are all currently available results.