Counting matching models…
Příchytka na čalounění - dočasně trvalé řešení zlomené příchytky. Tisknuto z PET-G a drží (z PLA praskla). Temporary (forever) solution. I printed it from PET-G and works fine (or ABS/ASA should be OK, from PLA it cracks - too fragile…
Place as much piranhas to the base as you can. Try it by one hand only. Share your best result with friends :)
Printed from PET-G with 3perimeters and 40% gyroid fill works fine. The “outside” part contains integrated support (blue part in model image). Remove the support when printed. Check how the part (especially bridge at 10.7 mm layer) is…
Printed from PET-G with 4 perimeters and 25% infill. no problem to store tool with weight up to 7 kg (and more but not tested :) for whole year - hot summer and cold winter. Happy printing ;)
Printed from PETG with 3perimeters and works fine :)
printed from PET-G, one body and 2 nuts. For body use brim, supports not required. if you need connector to 3/4" hose then set scale factor to 130% in X and Y coordinates for 1" hose connector set scale factor 200% in X and Y coordinates…
remix of the pen holder. See original model here . Thanks Ivan for it. when printed I recommend: to print the joining part with 100% infill. Use modifier to change infill localy (see image). to prevent tipping the model when pens are…
Printed from PET-G due to higher strength and UV protection. Use string of filament as the rotation axis of the flap. fasten ends in prepared holes with a soldering iron. Jako osa otáčení je použit kus filamentu. Konce jsou roztaveny…
Print base and some cat models. You can modify cat size in slicer to have more possibilities. When printed try to place as more cats you can to the base. Try to do it just by one hand. Who place more cats to the base is winner. Happy…
Print-in-once box for small headphones. It saves the wire to be without knots. Simply find the middle of headphones wire, put it into groove and turn …. Should be printed with small layer, there is risk the parts will be connected during…
just part of the hose lock. this is prepared to be used in your project. Is compatible with 1/2" (13mm) fastlocks (Gardena, Fieldman, Hozelock, etc.). For right production you need to use O-ring 11x2.5 mm or print is from Flex Printed…
Plug to the kitchen sink with 2" drain. Versions with/out hole for ring or chain for easier release from the sink. Printed from Flex (Gembird3 TPE, 15% fill, 2 perimeters) is bit tough but functional.
Stand for 2 Philips Sonicare Toothbrushes
feel free to remix
prichytka calouneni dveri auta. ve sliceru je třeba nastavit “detekce tenkých stěn” aby se správně vytvořila první vrstva včetně křidýlek. Pokud potřebujete úchytku upravit, zde je zdroj https://www.tinkercad.com/things/ddFXnxxtSBB-autocudl
slightly modified model to ensure the carabiner is pre-sprung with additional central ball which works like “lock” recommend to print from PET-G.
Pila nemá bednu a není ji kam šikovně strčit. Navíc musí být ve vodorovné (víceméně) poloze, aby z ní netekl olej. Tak šla nakonec na zeď.
Holder for Prusa Mini filament sensor to keep it turned up. It's recommended when the filament spool is placed above the printer (some extra spool holder is used).
SD card slot filler plate for DELL notebooks. Tested on Latitude 5591, can be easily modified to be used with other models. Model respects Standard SD card size (32x24 mm).
new ends of legs of small home ladder. Printed from PET-G with 3 perimeters and 25% infill. Fusion360 model attached
Really simple (minimalistic design) models of personal tag supporting multicolor and imprinted objects. Attached models are prepared to imprint safety pin or magnets (two small magnets required). Before printing there is required to do…
replacement part of lost part of the cross-country ski bindig Náhradní patka vázání. Vázání Fisher, systém rottefella
replacement of the chain clutch for Marantec garage door. Printed from PET-G and seems to work fine. Form ABS/ASA it will be faster.
Cover contain locks on the bottom side. There are wire holders which can be adapted depends on the wire/cable diameter. PS about picture: I used wrong profile so the corners detach from heatbed …
printed with a 45 degree angle for greater strength
The replacement of the capsule container. Made from PET-G with supports. Model is slightly improved to the print on images. ------ Náhrada šuplete na použité kapsle. Model je oproti fotkám ještě trochu upravený, aby lépe seděl v kávovaru.
Hacek na uchyceni svetylek na hlinikove pergole
Chtěl jsem měřáček, který lze vytisknout a hned použít, bez nutnosti skládání, lepení atd. Měl jsem ho i s vytištěnou pružinkou, ale ta se hned unaví. Ovládání prstem je prostě nejlepší :)
Tube thickness is 2mm, to prevent breaking of the part I printed it from PETG with 100% infill pro zajištění pevnosti je stěna 2mm tlustá a vytisknul jsem to z PETG s 100% výplní. Zítra otestuji v autě :)
just another token to schoping cart with canoe symbol
Original model is very simple to open. Here you can download lockers modified as a maze. To prevent core part to rotate during the opening, I added "rail" to guide the core in base part. Just modified parts of the original model attached…
Probably you need to modify the model to fit your poles… see model source on the kinder CAD ;)
replacement of lost part of the cross-country ski bindig Náhradní krytka zámku bežkařského vázání. Vázání Fisher
First print rollers (2 pieces). They should be little bit heavier, so I printed them with 100% infill. Then prepare print of the body. When slicing insert the pause command at height about 10-12mm to place rollers inside the body…
These are all currently available results.
