Counting matching models…
Makes swapping batteries a lot simpler by keeping the body connected to the chassis. Uses the stock mounting points. Replaces the rear bumper mount and the mounting bracket connected to the roll cage on the body. 2 additional M3 holes are…
A scale accessory for scale crawlers. Designed at 1/10 scale. 32x22x12mm. Category: R/C Vehicles
This adapter allow you to drive an RC car one-handed, use your index finger for throttle like usual, steer with your thumb. Great for driving between obstacles on a crawler trail or when you're also trying to film while driving. The inner…
The panhard bar on the SCX6 is mounted single shear on both ends. No bueno. This brace reinforces the mount on the axle. Uses the stock hardware, no additional parts needed. To reinforce the chassis mount I recommend a metal shock tower…
A trailer hitch that bolts up to the SCX6 rear bumper mount without any mods. I broke the ball hitch pretty quickly but it is holding op nicely now in TPU. Required hardware: 4x M4x22mm 1x M2.5x10mm Category: R/C Vehicles
A second valve cover for your SCX6, based on the same thing for an SCX10III. Print without supports, stick on your steering servo with some double sided tape. Category: R/C Vehicles
Exhaust tips for the Element RC Knightrunner. Cut of the stock plastic tip, these tips are designed to fit over the stock 7mm exhaust pipe. Category: R/C Vehicles
Print in TPU, mount using the screws on the sides of the windscreen.
Chassis kit: https://www.axialadventure.com/product/1-10-scx10-ii-4wd-raw-builders-kit-v2/AXI90104V2.html Body kit: https://store.rc4wd.com/RC4WD-1985-Toyota-4Runner-Hard-Body-Complete-Set_p_7220.html The rear hinge comes in 2 parts. Use…
My Arocs 3348 was sitting a little low in the rear. I created this spacer to lift it a little bit. These spacers are designed to work on the front and the rear. The center hole fits over the rivet holding the spring leafs together.…
The clasp is ideally printed in TPU and can be glued into the door. PLA/PETG/ABS should also work after sanding it for the correct fit. Flip in your slicer software to get both sides. Prints without supports.
Sometimes the brewing unit will get jammed. This keys makes it a lot easier to open the brewing group to rinse it on the inside.
A small and simple side mirror for your VS4-10, or other RC bodies. Prints flat on its face, no supports needed. I printed this in TPU so it flexes instead of breaking. Stick on a circle of aluminium tape or tin foil for the full effect.…
Printed in TPU for a less noisy ride. 4mm thickness. Mirror 1 print for the rear tires in your slicing tool. Should fit many Wilesco model steam engines, rescale for other models.
Print 2. It's best to print these at an angle for strength. The include 3MF files print the model at a 45 degree angle with minimals support, 3 perimeters and 15% infill. I printed my set in PETG.
Decorative trailer hitch for the stock Knightrunner bumper. Designed to print in TPU or other flexible materials. No fasteners needed, it will clip into place. Category: R/C Vehicles
This replaces the original tray with no other mods required. It takes up the same space so should not interfere with other mods. Even slightly lowers the battery. Max battery size: 151mm x 50mm. Includes slots for a velcro strap. Prints…
Print 4x in clear material. Paint with red and orange clear paint, I recommend Tamiya X26 & X27. Glue in place. Holds 3mm LEDs. Requires a 5mm hole in the body, drill though original sticker for correct placement.
Oct 2020 update: the scale in the STLs was wrong. Use the fixed versions or print the originals at 10% scale. A set of mounts to attach a Team Raffee Benz G-class hardbody to a MST CFX-W crawler chassis. Replaces the rear bumper mount,…
I purchased this body model for an Axial SCX10ii and created some additional parts for it. https://www.cgtrader.com/3d-print-models/hobby-diy/automotive/jeep-grand-cherokee-1977-body-for-print The lights are for the left side only but you…
I had 2 fenders on my VS4-10 snap where they are bolted to the chassis with 2 bolt next to each other, near the bumpers. Maybe I screwed them in too tight. These washers are supposed to reinforce that area. Print 4, one for each corner of…
These are all currently available results.
