Counting matching models…
An adapter to replace the 4010 extruder cooling fan with a 4020 blower fan. Has good clearance with the gantry, no change in build area. Mounts to the stock extruder with stock screws, 4020 fan mounts to the bracket with 3× M3×18 bolts.…
A simple holder for a generic Multimeter, 72×52mm box size and ⌀10mm Probe holders. Builtin support for the hooks that easily snip off with flush cutters, no other support needed. Walls are 1mm Derived from a Skadis Storage Box by…
Ersatzteile für Braas Atelier BA91/AF81/AF86 Dachfenster: Griffhebel, Konsole und Schieber. Die Modelle sind für die linke Seite, für die rechte Seite das Modell im Slicer spiegeln. Replacement parts for Braas Atelier BA91/AF81/AF86 roof…
A little clamp that arrests the accelerator lever paddle on an e-scooter with a ⌀22mm handle bar in a fixed position by friction. This sets the throttle to a certain position while avoiding sore thumbs.
A mounting bracket for the Klipper Screen ADXL sensor to the extruder stepper motor. Requires 2× countersunk M3×20 screws to replace two of the the stock stepper motor screws. This works specifically with the sensor included with Sovol…
A mounting shroud for a 4020 blower fan onto a Sovol SV06 printer for parts cooling. The blower fan is mounted via pressfit into the shroud and clears the gantry on both sides. It prints “face down” as one part, supports are required for…
A fixed mount for a ⌀8mm endoscopic camera. This mount uses the boltholes for the stock nozzle cooling fan mount, so an alternative nozzle cooling setup is required. The camera points at an angle straight to the nozzle and the cable does…
The threads where the cable bracket is mounted are easily stripped. This bracket mounts to the extrusion with an M4 T-nut and provides a new mounting point for the stock cable.
A tool holder for Skadis pegboards, for tools with hexagonal handles and 14mm circumscribed / 12mm inscribed diameter. Prints upside down without supports. Fits the handle of generic deburrers sold on amazon.
A tool holder for the includes sizes of hex keyt that clips to the top of a Sovol SV06. Prints “upside down” with no support.
A nut for 8mm Roller Skate Axles (5/16-24 UNF Thread, 608 bearings). The thread has been modified for a tighter fit with slight Interference. The nut can be driven with a ½ Inch (13mm) hex wrench. Prototype has been printed in PETG with…
A spacer for the Klipper Screen mounting bracket. Fits Sovol SV06 and SV06+. Attaches to the original bracket with one M4×20 Screw.
A Remix of "Low profile shock absorbing feet for 2020 V-slot (single) profile" with a Twist Clip
Replacement pivot cups for PowerDyne Thrust Plates before June 2020 (The ones that are no longer made). These have been used over several months by competetive roller derby skaters and so far proven to be a suitable replacement. There are…
A paper towel roll holder that attaches to an Ikea Mosslanda shelf. Mirror it in your slicer to print the second part. For rolls of an inner diameter greater than 40mm and up to 55mm roll thickness.
A magnetic case for the M5Stack StopWatch ( Store , AliExpress ) for a better Grip. Uses 4 6×3mm round magnets for holding the device. Has a passthrough for straps and cable, protects the power button from getting accidentally pressed.
A replacement endcap for Monacor TM-25 / Seikaku ER-55S Transistor Megaphone. The walls are strengthened at the hinge mount and clip, therefore the plastic part that holds the Microphone PCB and contacts needs to be slightly modified.…
A replacement clip for clothes drying racks, ⌀ 16mm and 4mm
A wall mounted bracket to hang roller skates. 60mm radius to fit most wheels. Print two per skate and mount them about 40mm apart to fit the trucks.
A small tool to assist in the reassembly of 608 bearings: Holds the bearing balls in position in the outer bearing race to facilitate the replacement of the inner bearing race. Works with all disassemblable 608 bearings, such as those…
A holder for an universal drill chuck key for Skadis
A single peice table stand for classic tapered microphones, modelled specifically for Sonor K1
A replacement Knob to tighten the M8 nut of a hand saw. Prints without supports due to builtin 0.2mm bridging layer.
This is an extension for N60 Camera Mount Arm for SV06 with 34×37mm ⌀2mm screwholes. It fits into the slot fot the Camera and extends it outwards by about 100mm. I needed this to mount a camera with a broken base at a greater distance.…
These are all currently available results.
