Counting matching models…
When loading the case feeder tubes on lee 1000, lee loadmaster, lee 4000 or lee sixpack pro you are limited to midrange pistol cases, 9 mm do not collate well and .223 cases won’t work at all. This collator will allow the loading of cases…
This packer allows you to raise the cheek piece on the any Sako TRG rifle by 3 mm. The TRG 42 cheek piece can be raise by 2 of these before the cheek piece interferes with the action of the bolt. No idea if the problem occurs in the TRG…
Using solid waste pipe allows the grey water to drain faster than flexible pipe but it needs supporting. These brackets clip on to the UK size waste pipe of 32mm and 40mm. The 32 mm pipe will also slide inside the 40mm pipe to allowing…
This is a powder baffle for the new lee powder dispensers with the transparent hopper. The baffle fits in to the red hopper cap and is held in by a screw in locking collar. Print Settings Printer Brand: MK3 Printer: Prusa i3 Rafts: No…
Storage rack if you have two or more presses. This plastic dual rail block allow you to safely store your additional presses on any flat surface by screwing it down with standard 4mm screws . By adding addition centre blocks you can mount…
The latest accuracy international magazine holds the bolt open when empty, this can be very annoying if you want to shoot it as a single shot. This adaptor sits in the top of the magazine and allows the rifle to shoot single shot. To…
When measuring power off the press this powder die and funnel makes it easy to pour the powder from the scales pan in to the case. It can either be mounted in a turret/progressive press or in a separate stand. This is not a load bearing…
Unit for lubing several cases at once using this lube roller and lube pad Print Settings Printer Brand: Prusa Printer: i3 MK3 MMU 2 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: any PetG Red Category: Sport & Outdoors
device clips between the two right hand columns on the lee 100 and deflect the odd rouge primer in to the correct place Category: 3D Printing
This is an improved version of one I found on the internet. It directs the primers to the bin and the outlet shoot does not interfere with the latest ram linkage. The bin is of my own design and has a removable side to allow easy…
When using the Sinclair expander mandrel with .223 Remington the case can hit the mandrel pin or go up the side of the pin which damages the case, when used with 300AAC blackout the body of the die is to long for the mandrel to fully…
This is a two part collator tray for Remington .223. the parts may requiring some fitting before being glued together. Off the 2 I have printed on a Da Vinci jr have gone together with a press fit no tinkering required Category: 3D Printing
When loading the 338 lapua on my progressive press I often like to weigh the powder loads and add them by hand. this die goes in place of my powder dropper and allows me to do this. It was printed at the best definition my printer will…
When the Sabbatti MMR tactical rifle is fitted with a 56mm scope the cheek piece has to be raised to its limit and sometimes beyond. Depending on calibre this either stops the bolt being fully cycled or prevents its removal without…
When reversing a caravan it can be difficult to see when the back end starts to turn. This unit screws underneath the caravan and sticks out the sides and can be seen on the towing vehicles mirrors. The unit is in 2 pieces, the bracket…
A die stand for use in conjunction with the powder through dies with funnel I have also uploaded. There are 2 versions one is screwed down to the reloading bench, the other can be gripped in a vice by the block at the bottom. Print…
Rear bag height adjuster for Protektor Bunny Ear Rear Bag w Hard Bottom 14A or similar size bags. These packing blocks interlock to give a firm base for the rear bag when the bag is not tall enough for the front rest. Print Settings…
When using the Sinclair expander mandrel with .223 Remington the case can hit the mandrel pin or go up the side of the pin which damages the case. This insert is a press fit inside the Sinclair mandrel die body and aligns the case with…
By restricting the small tube the auto trickler V4 throws mor consistently but slightly slower. When you have printed the part running a 3mm drill down the hole will clear out any whiskers. Be carful when doing this as if to much torque…
When storing my auto trickler between loading sessions i found the hopper can be easily knocked and is very tall, taking the hopper off helped but then the hopper can be knocked over. This is a stand that gives the hopper a stable base.…
The original shop glass does allow the power to bounce out and scatter over the scales platen. this cup is designed to stop powder bouncing out, printed in Pet-G or PC-CF at .20 or .25 layer height. Supports needed for the handle. only.…
These are all currently available results.
