Counting matching models…
This is an XT30 / XT60 / XT90 Cap, it fits over the female side (battery side) of lipo batteries. It has a small lip on the bottom to make it easier to pull apart. Should fit snug. I use these to determine if the battery is charged or…
Design Once I finally received notice my LTT Screwdriver shipped I went looking for a nice case / organizer for it and wasn't able to find anything that met my requirements. So I took the Rugged Box (Parameterizable) from Whity and the…
Upgraded Wheel and Tread system for the Segway Navimow i Series! When I first got the Navimow I was so disappointed I was planning on returning it. It couldn't navigate the grass at all. It would get stuck left and right. I turned to…
3D printed Frag Rock for the reef aquarium. I was recently searching for 3D printed frag rocks, and sadly I wasn't very fond of the ones I found. I wanted some more exciting curvatures. So I decided to make my own. These are meant to go…
This is a little spacer (printed out of TPU) that allows the DJI O4 Air Unit “Lite” to fit into frames that have spacing for a 19mm camera. It also allows for a small amount of vibration absorption since it's not very rigid. I used the…
This is a simple yet effective egg-crate rack holder. They are stackable and have locations for zip ties so you can zip tie the egg-crate to the stand, and the stand to other stands to increase the height. The egg crate diffuser I have…
This is a little spacer (printed out of TPU) that allows the DJI O4 Air Unit “Lite” to fit into frames that have spacing for a 19mm camera. It also allows for a small amount of vibration absorption since it's not very rigid. I used the…
Update - The magnets used in this designed (and linked below) do rust after months in the aquarium. I highly advise users to only use for short periods at a time. I purchased some newer magnets (capable of holding more weight too) and…
Costco recently had 3 packs of these flashlights on sale for $20. Really like these flashlights as they can be both rechargeable or use AAA batteries. With a focusable lens they seemed to be a great all around flashlight for the house. I…
Description This is a simple wall mount for the Ego Hedge Trimmer to allow it to be mounted to the wall. It grabs onto the handles beneath the base. Smaller batteries can be kept on it while in this storage mode, but I would not encourage…
This is a phone / small tablet stand for the "Sunny Health & Fitness Indoor Exercise Stationary Bike with Digital Monitor and 22 LB Chromed Flywheel" Model # SF-B1203. It is designed to go around the handle bars and hold the phone in a…
This is a adapter to fit regular (12oz cans) and slimcans (redbull, whiteclaw, truly, etc 12oz can's) in the taller 16oz "craft can" sized double walled aluminum koozie. This was made specifically for the RTIC Craft Can Koozie, but may…
This is a "stronger" and "taller" version of an RTK mount. The original was a good base, but he antenna was still below the roof line. This brings it up higher and is extremely strong. The weakest point is probably the two screws that…
This adapter will allow you to mount the Segway Navimow (i110 at least) RTK to chainlink fence posts. This may allow other "poles" that are about 1" (25.4mm) thick to attach to chain-link posts. There is a extra little "hole" on the side…
Created this so that tools that have belt clips or the tools that have other reasons why they can't be pushed up against the wall can still be mounted. Honestly, I didn't do the best job on this, you need longer screws. If I took the time…
This is an attachment for thread boards to allow users to store their dremel bits to their walls. This holds 45 bits if they are all "narrow" at their head. So you may not be able to fit as many. Holes are 3.8mm diameter, so other things…
This is an attachment for thread boards to allow users to store their Pittsburgh 1/2 in Drive Impact Deep Socket Set, 13-Piece . They are labeled and were originally measured for the metric set. The SAE set doesn't have perfect spacing,…
This is a replacement Build Plate Mount for the Monoprice Mini SLA printer. My build plate mount broke the other day and tired of waiting on Monoprice for a replacement I decided to 3D Print this. This is beefed up a little here and…
This is an attachment for thread boards to allow users to store three sets of tape to their walls. Tape diameter should be 57mm (2.25") or smaller with a width of 23mm (.9") or less. Once again, you need to have purchased thread boards…
E3D Titan Extruder mount that has both a spot for a fan and an inductive sensor mount. This is designed for the orange tip inductive sensor (LJ12A3-4-Z/AX DC 6-36V NPN NC 4mm Inductive Proximity Sensor Switch). The inspiration for this…
These are all currently available results.
