Counting matching models…
Light globe for a ceiling fixture with a 3.25” OD neck. I like that it hangs from my ceiling “upside down Rogue One fashion” instead of with the laser aperture disc “above” the equator as it’s depicted in ANH and Jedi. I did notice that…
Update Note: V8 .3mf file is revised based on a chunk of model I got from Tailfin. The new design matches the compound contours of the rack arch beautifully , but I didn't include the .F3D file of that version since I don't own the…
I designed this so that I could use my flight simulation rudder pedals without my office chair swiveling. To engage the brake, I use the lever built into the chair to lower the seat onto the printed column. There's grippy stuff on the…
Might fit in other rail systems, but designed for the T-track in the Festool MFT3.
My Virpil MongoosT50 CM3 throttle lives on a swivel chair. The cables stick out from the front, and I'd like them to not get bashed by my carelessness. Hence, a bash guard. I think it'd fit a CM2, but I don't have one to try. Replace the…
This was designed to accept a pair of heat-set M5 inserts. I haven't done any rough-terrain testing…I designed this to accept a pretty lightweight bike lock. I'd keep an eye on it (or use some through-bolts and washers) for a heavier load.
This is a simple bushing and roller assembly to hang a roll of filament on a Skadis pegboard. Requires (2) 608 bearings and (1) IKEA Skadis 3 ¾" hooks (maybe 95 mm? Not sure how they're advertised in metric). The outboard bearing should…
Pretty simple. Fits the Tasogen thermometer/hygrometer you can get by the gross on Amazon.
Yep, you could design this yourself. But here's a quick .3mf with the PrusaSlicer 2.6 split and pin features. If you're not using them you should be.
Print two of these. I used PETG, PLA might be a little brittle but is probably strong enough.
This is designed to locate a Qi-enabled device to align to the charging coil, using the base of a PopSocket swappable grip. On my phone (iPhone 11), the Qi charging loop is approximately centered. The PopSocket base is in the middle of…
Lanyard loop for the Aukey USB-C to USB-A adapter that's cheap on teh Amazonz. This is press-fit. There's no retention for the part, which I discovered when I dropped one into a hole in the bottom of my car that is inaccessible to any…
After creating the keeper for my plain cap, this was the obvious next step. You should buy a DrinkTank: http://drinktanks.com Here's the plain cap if you need it: http://www.thingiverse.com/thing:2095569 Don't carry your growler by the…
Note that the lock ring is left hand threaded.
I wasn't kidding, I'm putting lanyards on everything. Attach your lid to your DrinkTanks insulated growler. You don't have one? Fix that. https://www.drinktanks.com/ I feel like I shouldn't have to say this, but if you carry your growler…
Sized for the Ryobi small cordless glue gun, but it should stick anywhere flat. The holes are to increase the engagement with the hot glue pool, make it stick to the surface better.
The uploaded model is slightly different from the photo, but you get the idea. Snap fit on the long Skadis hook.
I designed this to fit on a ruler 2" wide and 3mm thick (yes I mix units. It's gonna be OK.) I set up the 3mf with a layer change operation that highlights the crosshairs around the marking hole. Use a contrasting color to enhance the…
I designed this to give a rough idea of scale for photographed items. If you want to reverse engineer a photo, you'll want something with more precision. This is for getting a scale idea for larger objects. Designed with a color change…
I added a little cavity to slide a piece of filament, to tighten up the dovetail. Makes the fitting a little bit more secure. It's a good design! Works great! The headset side just snaps onto the strap mount. The triangular "toe" points…
These are all currently available results.
