P
PrintablesCocoMonGo
Meanwell LRS DIN Slideable Side Clip
This is a remix of DIN clips for Meanwell LRS 200 PSU by neon.blue
- Downloads
- 278
- Likes
- 51
- Rating
- 5
All models
Counting matching models…
P
PrintablesCocoMonGo
Absolutely Low Friction Filament Drybox using the Ikea 365+ 10.6l
I had a lot of problems with filament being stuck due to the higher friction of pulling out of the Ikea 365+ container and through 1.5m of reverse bowden. I liked the version created by AlexMu but there were things that I thought could be…
- Downloads
- 156
- Likes
- 41
- Rating
- 5
P
PrintablesCocoMonGo
Raspberry Pi 4 Passive Heatsink Case
Based on the design by Drew_B and using the dummy Rpi4 model by Olvin, I created this Raspberry PI 4 case to attach it to my Ender 3 v2 sides. It is designed to have minimal impact to air flow obstructing the massive aluminium heatsink,…
- Downloads
- 108
- Likes
- 11
- Rating
- 5
P
PrintablesCocoMonGo
Ender 3 v2 X & Y Gantry GT2 Holder for Increased Accuracy
Update 18 Apr 2022: The Y-axis mod suffered significant deformation probably due to heat from its close proximity to the heated bed even with insulation. Suggest to have this printed only in ABS at this point of time. Update 7 Apr 2022:…
- Downloads
- 65
- Likes
- 9
- Rating
- 0
P
PrintablesCocoMonGo
VOC Scrubber - A high efficiency Activated Carbon & HEPA Filter
Overview VOC Scrubber is a combined VOC and HEPA filter using activated carbon pallets to remove fumes and particles generated during 3D printing. Initially developed with the Voron 2.4 in mind, it should also fit Voron Tridents and other…
- Downloads
- 54
- Likes
- 37
- Rating
- 5
P
PrintablesCocoMonGo
Prince O3 Hybrid Hornet MP Lower Grommet
This is a design for the replacement for the Prince O3 Hybrid Hornet MP (100 sq. in.) tennis racket 6 o'clock grommet which is made of some soft rubber material which unfortunately does not survive very long. Given enough time the rubber…
- Downloads
- 27
- Likes
- 3
- Rating
- 0
P
PrintablesCocoMonGo
Neoteck Dial Gauge Remix
This is a remix of Neoteck Dial Gauge Slot Mount Ender 3 Pro (2020/4040) by falo2k. Issues with previous version and remix solution Original version had the dial gauge fitting snugly within the mount, but a very minor amount of play which…
- Downloads
- 24
- Likes
- 1
- Rating
- 0
P
PrintablesCocoMonGo
Hasselblad PM45 Cold shoe Cover
A simple cold shoe cover specifically for the Hasselblad PM45 however it should fit other Hasselblad 45-degree prism finder with a similarly spec'ed cold shoe. Unfortunately I only have the PM45 to test, fortunately it only takes a few…
- Downloads
- 4
- Likes
- 1
- Rating
- 0
P
PrintablesCocoMonGo
120 Film Snap Holder
This is a remix based on Spicy3D's 26800 battery container model, resized and remixed to add strength especially by changing the hinge to 1x M2 35mm Hex Bolt and 1x M2 Heat set insert. They hold 3x 120 format film with or without their…
- Downloads
- 2
- Likes
- 0
- Rating
- 0
These are all currently available results.