Counting matching models…
This mount is designed to attach an ESP32-CAM microcontroller to a water meter. Together with the open source firmware "AI-on-the-edge" ( https://github.com/jomjol/AI-on-the-edge-device ) of the user Jomjol it can read the water meter…
a minimal case for a HC-SR04 sensor, fits without screwing.
This is a bike Freewheel (not cassette) remove tool. Be aware that the Freewheel is mounted with high torque and the plastic tool may not hold up.
This is a minimal case for a IR sensor (Reflective Optical Sensor TCRT5000). The sensor dimension are approximately 30x14mm sensor fits inside the case without the need of screwing or fixing in any other ways, but a screw hole is present…
Simple Fox Fork Topcap Socket, 26 and 32mm, flat bottom, ½" drive. Be aware that the topcap should be tightened to 25Nm and some 3D printed plastics may fail at that torque I printed it in Ankun PLA+, since PETG Did not work.
A simple snap fit case for a 2.8" ili9341 LCD display opened in the back might not fit all displays, as there are differences among different manufacturers, please check the basic dimensions of your display first.
handle for a metal saw blade; rúčka na pílový plát
headlamp plates, different versions uchyt celovky, rozne verzie
This is a hook that can be mounted into the floor rails of an Renault Espace IV used for fitting the seats. To connect the bottom and top part just use a M8x30 screw and nut (with 13mm hexagon head). Put it loose into the rail and begin…
These two tools are meant to remove the piston covers from older Magura brake calipers such as the Magura Marta and Louise. they are adapters to a Hex key
Simple DIN rail mount for Huawei OptiXstar EG8010Hv6 modem. Part1 and Part2 should be glued together
A cover for the bottom of the crown for a Rock Shox Reba Race Prevents dirt and water going into the steerer tube. You can print it in a color that suits you and you fork/bike design
Fits the avid juicy series brake levers, maybe newer too. Usage at own risk , as plastic is less durable then aluminum! The lower strength is considered in the design but not tested!
replacement screw for a tripod
a Shimano RT-EM300 Magnet ring. a 7mm diameter magnet should be placed into the hole and glued in place / hole filled with glue as in original printable without supports
Marzocchi Bomber DJ rebound cover in a bit different design - shorter and wider. Has all the features as the original cover - thread, surface for sealing, its lighter and you can print it in a color that suits you. The height is minimal…
a optical cover for the crush washer and nut on the lower leg of Marzocchi Bomber DJ fork. Fits also various other Marzocchi and Fox forks. You can print it in any color that suits you and your fork / bike design
a Simple plug for a 13pin car trailer power outlet, if the original is damaged. It simply plugs in the same way as the power cord. if it has too much play in the plug, just use a bit of electrical tape or similar in the inside to…
Halogen uchyt (Halogen lamp bracket) a simple bracket to quickly mount a halogen lamp
A simple cover of the bottom of the fork crown for Marzocci Bomber DJ. Prevents dirt and water going into the steerer tube. You can print it in a color that suits you and you fork/bike design
this is a flange to mount and additional inlet / outlet directly on a 150mm steel pipe of the ventilation system. the inlet / outlet diameter is 90mm and has an adjustable lid. To assemble it you need an M5 threaded rod and three M5 nuts.…
print in the desired position (on the chamfered surfaces) without supports. v2: stronger version
An alternative rebound adapter/adjuster knob for GRIP on Fox stepcast forks. Put on - adjust - pull out a Fox 2022 Perf SC 32 Float 29 100mm Grip fork was used for reference, but the adapter should work for most forks with GRIP damper…
These are all currently available results.
