Counting matching models…
Update 06-01-19 It turns out that the 3x3x3 model wasn't quite levelled correctly, thanks to hojokono for pointing it out. I have now re-uploaded the model so that it lands squarely on the bed in your slicer. Update 16-1--16 Added a…
I designed this to keep my batteries safe from shorting out after charging. This is for the flat top 18650 battery but the button top ones will fit if you don't screw the lid down all the way. The pictures don't show it, but I have added…
Designed in Fusion 360 from inspiration from Makers Muse video. The picture shows it scaled up to 200%. For scale, the bed is 400x400. If you print this at normal scale, you may need to use a brim. Printed on the #Borg (CR-10s4 on…
A relatively quick print that will save you from having to lean your pictures against the wall or other ornaments. The stand measures 141wx125hx90d The channel is 6.5mm wide. The pocket behind and under the picture is to accommodate the…
Designed in Fusion 360 and printed on the Borg (CR-10s4 on Steroids) This was for my neighbour that had just got a Guinea Pig for their little boy. Print instructions Platform Dimensions 280mm x 280mm x 160mm Printed in PLA on the Borg…
This is just another version of my previous Lattice Cube. This one has 2 cubes rotated on the x axis, Print instructions Unassociated tags: Lattice cube Licence: Creative Commons - Attribution - Non-Commercial - Share Alike Category: 3D…
Update: Added another Inner vase with a 4mm base so that it does not get stuck in the outer if it's screwed in too far. This was inspired by Devin @ Make Anything on YT. Devin created something similar in Solidworks. But since I use…
I spray my models outside, so I created this simple tool to hold them while spraying the primer. Simply add a small piece of double sided sticky tape or blutak to the top, then stick your model to it. The wide base will help to avoid it…
This was inspired by Chaos Core Tech and his wife, they have an awesome Youtube channel with a ton of 3D Printing tutorials and advice. https://www.youtube.com/channel/UCVmyytnqQrcTg1WRFXTo14Q They are the ones that got me into painting…
Linax created this awesome model that I simply had to make. Thank you Linax I did find a couple of small changes that I wanted to make; The bearing now has a shoulder to hold it in place, the internal square hole is 0.2mm smaller, again…
Designed using Fusion 360 to replace the original because, the original split down the shaft. There were a few prototypes to ensure that I got the hole just right to slide on the switch, with just the right amount of tolerance. Print…
Some of you have commented that this does not lay flat on the build plate. I also found this to be the case, so all I have done is made each part lay flat (with S3D), I haven't made any other changes at all. Hope this helps Print…
Update 01/10/2018 As requested by BlueMaster27, I have added a main body with fixing lugs and the Sonoff insert included in one stl 'Main Single Entry with insert and fixings.stl' I have also raised the Sonoff up by 1.5mm to make the…
Yep! Another load of fidget spinners :-) Designed in Fusion 360. Sliced with S3D. Printed on Prusa i3 MK2. All the bearings are standard 608zz skateboard bearings (8x22x7mm) The nuts are standard M10 (8mm thick) The steel balls are 13mm…
Great test idea, thank you Vicky. Hope you don't mind me remixing. When I sliced the original in S3D, I noticed that some of the numbers would not be printed as part of the main body. I'm not criticising the original design at all. It was…
I found that the original CR-10s spool holder was too close to the printer, so I printed a stand-alone one. This gave me some wasted space on top of the control box, so I decided to utilise the spool holder thumb screws to a tool tray.…
Update 12/03/17 As requested, I have also added mounting slots instead of just holes Extended the HyperCube fan duct by 10mm, as requested by RalphVigg. Print instructions Licence: Creative Commons - Attribution - Non-Commercial - Share…
Found a Batman font and added the name in 123Design. It's for my friends son who loves superheroes. Print instructions Licence: Creative Commons - Attribution - Non-Commercial - Share Alike Category: Signs & Logos Print Settings Printer…
This is to hold supplies of Dish Cloths and Bin Bags. Receptacles are 85mm 75mm and 45mm in diameter and 100mm deep. Printed on pimped up CR-10 S4 in 3DPrintz PLA Sliced in S3D; 0.32 Layer height 2 Perimeters 5 Top 3 Bottom layers Speed…
I wanted to create a top plate that I could mount things on without having to destroy the original. So (naturally) I decided to 3D print one with the intention of adding mounts for LEDs and the MeArm etc. However, I got a little…
If you have a spool holder that the wingnuts could snag on, this is your solution. I recently purchased my first #MasterSpool from Rushmere 3D https://www.jays3dadventure.co.uk/Shop/index.php here in the UK. I was concerned that my…
Go buy and build a DiddyBorg, you'll be glad you did. It is a fantastic machine and all the controllers are designed in house too. The after sales support that these guys offer is nothing short of perfection, and they really know there…
Another little addition for my DiddyBorg from https://www.piborg.org/ This time it's a guard that clips over the motors under the DiddyBorg to help protect the motors and electronics when you're driving over rough terrain. Print…
These are all currently available results.
