Nextion NX4832F035 3,5 inch display case
Case, designed for NX4832F035, but can fit for all similar models. Print parameters Supports: No supports necessary, place it facing down if you have enough cooling
- Downloads
- 517
- Likes
- 9
- Rating
- 5
27 models
Case, designed for NX4832F035, but can fit for all similar models. Print parameters Supports: No supports necessary, place it facing down if you have enough cooling
Included in the attachments is the parametric Fusion 360 design and the label design
This is a functional and aesthetic case for the STM32F429-DISC1 board. Gives access to all of the necessary GPIO pins/inputs, screen, and peripherals. The case is a 2 piece design with a bottom and top shell. Assemble with 4-M3x12 socket…
Couldn't find any printable case for my new dev board, so I went to design my own. While doing it, I had to model the board itself first. This is a simplified 3D model of the new Black Pill development board with stm32f4xx (I got the…
A simple case for new black pill dev board (version with stm32f411x, should be compatible with stm32f401x, not to be confused with old black pill with stm32f103). No screws needed, top should snap on the bottom. Bottom holes should fit…
This model is compatible with the lego system.
HP 32F Monitor Vesa Adapter really wanted the ability to raise/lower my 32F LCD. found other Vesa adapters for smaller HP Monitors here on thingiverse, but none fit my 32F. works really well. be sure you trust your printer/filament Print…
Software and assembly video here: Case is ideally held together by either melting with a soldering iron or just using glue. Electronics Used (Including Purchase Links) WeAct Studio STM32 Core (STM32F405RGT6):…
Hikvision base, one tilted by 14°, one normal. With hole for a PG16 grommet for ethernet cable. Included small grommet/end cap for microphone cable, if you have "-IS" version. A low ring is for testing. Layer 0.25mm, Nozzle 0.4mm, Infill…
Software and assembly video here: Case is ideally held together with 15mm M3 self tapping screws. Electronics Used (Including Purchase Links) DIYMore STM32F407VGT6: https://www.aliexpress.com/item/1005002186031065.html 2.42 SSD1309 SPI…
Marlin 2.1 Kingroon KP3S mks_robin_nano_v1_3_f4 STM32F407VET6
Small case designed with the STM32F405 feather board in mind. It has a button for the reset switch and a slot in the rear for memory card access. No provision for LiPo battery connector or I2C (yet). Also tested and working with Bluefruit…
M32F25 + step + Fusion 360 I did bring osVAC to Fusion 360. The link to the latest version of the files can be found here: Ich habe osVAC in Fusion 360 nachgebaut. Der Verweis auf die immer aktuellste Version ist hier:…
slight change from original removed bottom access holes (I don't need them, I access all gpio pins from the top, bottom is just allowing crap from the table to make shorts) had to cut of pieces of pcb support as on number of boards…
This is a simple STM32F429-DISCOVERY enclosure, without screws, just snap-in connections. Cack site is for dust sensor.
Included in the attachments is the parametric Fusion 360 design and the label design
Frame for STMicroelectronics evauluation board STM32F750F-DK.
Minimalist bumper designed for the STM32F407G-DISC1 development board. Initial insertion of the board is tight; slide the micro USB side of the board in first before securing the board under the two 1.5mm retaining tabs. Printed on Bambu…
This is a sleek and functional 3D printable case designed specifically for the popular STM32F103C8T6 development board, often referred to as the “Blue Pill”. Why you need this case: Whether you're using your STM32F103C8T6 for embedded…
Software and assembly video here: There are two sets of parts for the top+bottom+buttons depending on the screen size you want. Case is ideally held together with 12mm M3 self tapping screws. Electronics Used (Including Purchase Links)…
I simple mount for an STM32F4VE that has a loop for a zip tie to hold the USB cable in place. Print Settings Printer: HEVO Resolution: 200 Infill: 15 Filament: Tecbears PLA+ Category: Electronics
This is a remix of the hand wired macropad VOID9 by Victor . Instead of the Arduino ProMicro this version fits a STM32F4x1 (aka "Black Pill"). I provide only the redesigned bottom part, please visit the original thing for the top pieces.…
To extend the Oculus Rift S up to 10 meter/16 feet, you need a DisplayPort repeater and a active USB3 Cable. all needed Products from amazon you will find below :) This Box is just to organize the cable stuff in the middle of the 10…
This enclosure is designed for convenient and safe storage of microcontrollers. There are also grooves on the sides for easy handling with tweezers.
Made this stand because the board doesn't come with legs and has breakout pins on both sides. The user should still be able to connect to the breakout pins and USB ports. I have included the FreeCAD model in case you want to edit the…
This is a remix of the hand wired macropad VOID9 by Victor . Instead of the Arduino ProMicro this version fits a STM32F4x1 (aka "Black Pill"). I provide only the redesigned bottom part, please visit the original thing for the top pieces.…