18 models
Print in black PETG for temp resistance. Print at least two for the most control of the cables location. The two small bump-outs are slightly different diameters. This is because my 12v and USB cables are different diameters. The…
I could not find a focus mask that worked with the celestron dew heater ring and hyperstar. This design elevates the mask so that the dew heater ring and the cables do not tilt the mask. Print it “face down”, I used PLA and 0.2mm leyer…
Printed in Black PETG on a Sovol SV07 plus.
Tri-Bahtinov Mask for C8 and Edge HD 8 Hyperstar with cooled ZWO/OGMA/Touptek 80mm diameter camera This Tri-bahtinov mask will fit C8 or Edge HD8 in the Hyperstar configuration with out having to remove the camera. outer diameter is 203mm…
What If you are using a Starizona Hyperstar for your EdgeHD 800 scope you need a way of routing the power and USB cables in front of the OTA. Since straight lines cause spikes, I designed this bracket to route the cables in a 180deg arc…
Hyperstar Cable Holder and Dew shield r for Celetsron 9.25" Edge HD Dew shield for small printers is here FreeCad code on github BOM 16x M3x10mm screw Optional W&W Astro dew heater 100 cm strap Camping foam mat for create extension tube…
If you have a Celestron CPC11 telescope with a Hyperstar installed then you likely want something to hold your camera cables. Attaching the cables to these guides means the diffraction pattern seen in your camera images will be…
This is not going to be something that is downloaded by probably anyone, but I wanted to share just in case. I am using a Celestron Nexstar 6SE scope with the Hyperstar Mirror attached from Starizona, and connected to the Hyperstar is a…
Cable Router for helping with star shapes on a Celestron C6 with a Hyperstar for astrophotography. I used gaffer tape to secure the cables, and it works well. Had a noticeable improvement on the star shapes, and they're much more circular…
This is Cuiv's Tri-Bhatinov mask he designed for use with a Celestron C6 and Hyperstar, but with a cutout to support the Celestron Dew Heater. This worked well, along with recentering the corrector plate, to significantly improve my…
A Tri-Bahtinov Mask made for collimating the Celestron Edge HD 8" (CST) and standard C8 version with a Hyperstar 8 v4 installed. With the Hyperstar 8 v4 installed the mask needs different slit sizes as well as a split design to allow for…
The standard HyperStar cable routers for the Edge HD 8" telescope work well from preventing diffraction spikes; however, they mount to the outside rim. Therefore, they can't be used with the Celestron rigid dew shield since it clips…
A Bahtinov Mask made for the Celestron Edge HD 8" (CST) which also should work for the standard C8 version. With the Hyperstar 8 v4 installed the mask needs different slit sizes as well as a split design to allow for installation with…
This is intended to be printed "nose down" to get the rim to print cleanly. No supports. PETG recommended. My physical prints measured a millimeter or two smaller than the digital model was specifying. I assume this was due to material…
This is an extension tube to mount a 21mm width filter drawer and camera with a 6.5mm flange depth to a Hyperstar 8 v3. I made this for my Celestron EdgeHD8, Hyperstar 8 v3, SVBONY filter drawer and ZWO ASI533. This extension tube is…
The most obvious problem of putting a Pegasus Astro SmartEye on a Hyperstar is that to look into the SmartEye your head is in the way of the telescope. (You could use a tablet to view the SmartEye output, but at that point, why not just…
The standard HyperStar cable routers for the Edge HD 8" telescope work well from preventing diffraction spikes; however, they mount to the outside rim. Therefore, they can't be used with the Celestron rigid dew shield since it clips…
This is an extension tube to mount a 21mm width filter drawer and camera with a 6.5mm flange depth to a Hyperstar 8 v3. I made this for my Celestron EdgeHD8, Hyperstar 8 v3, SVBONY filter drawer and ZWO ASI533. This extension tube is…
