Counting matching models…
This is a remix of a remix i made improvements so the iris would stop coming off track and jam. Here is the description they posted with the original model about how to print and process. (This is a smaller, 4-leaf redesign of emmett's…
Enemy status modes from Metal Gear Solid. Usually seen after hearing this: This colour print can be done without use of an MMU and can be done manually with a filament change at the appropriate layer when slicing in PrusaSlicer - for more…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Unjamming rod. Print as many sections as you want. Tie paracord through it whilst all segments are folded up. Knot both ends. Unfold, slide pieces to interlock. Pull paracord tight through end slot- there ya go. Rod.
I kept having “Failed to feed the filament into the toolhead" error messages. I discovered my filament was not getting past the buffer assembly mounted on the rear of the X1C. On my printer, the PTFE tube enters the buffer at a slight…
Howard the Duck - Lea Jamming - 1986 3D printable model.
Figment jamming on a guitar Tip: The tab on the bottom is designed for using something such as Sticky Tack (a reusable soft adhesive putty), to keep your artwork secure in even the strongest gale force winds :D I've also made the…
I designed this battery tower out of frustration with other battery holders, which would regularly jam when I would remove a couple batteries. This one should always replace the battery you remove, with a new one from behind it. It…
The SABOT, or "Self-Aligning Barrel Obstruction Tool," is a low-profile, collapsible blaster unjamming rod to clear blocked barrels in 3D-printed nerf blasters. Featuring a durable shallow chevron shape and two runs of elastic, this tool…
i created a lid with a hole for a drill bit to stick inside and keep the nozzle clear break off the supports afterwards ----------------------------------------------------------------------------------------------------------------…
Please see earlier version https://makerworld.com/en/models/79389 and see the disadvantages there i created a lid with a hole for a drill bit to stick inside and keep the nozzle clear. this will apply even if you carry the super glue…
The SABOT MOLLE Holster is a tactically mountable holder for the SABOT unjamming rod. Featuring an open container using the built-in tension of the elastic in the unjamming rod for retention, this holster is a perfect fit for 500mm of…
35mm hoch und 82mm im Durchmesser. Wer Elektronik einbauen möchte: Alles was Rot ist, sollte Transparent gedruckt werden oder durch Leds ersetzt werden. Hoffe im Innenraum ist genügend Platz. Um die Verschraubung müsst Ihr euch noch…
Es wurde eine Verschraubung hinzugefügt, um den Fitting am verhaken zu verhindern. Der Filamentausgang ist nun spitzer, um ein verhaken des Filaments beim laden zu verhindern. Es gibt nun 2 verschiedene längen. Die Vorderseite ist nun…
Filament lubrication - silicone oil - no bowden jamming. Universal Filament filter or dust filter (for 1.75mm) The first chamber away from the filament coil serves as a cleaning zone to remove dirt and debris. And the second zone closer…
Same model as the original but adjusted for 10x4.75mm magnets
A flexible rod that you can use to clear jams from your dart blaster. You will need a length of paracord to hold the assembly together. Print as many sections as you need for your length of barrel.
A simple plate to glue over the two exhaust fans prevents the cable from getting stuck in the fan frame, as shown in the photo. P.S. I suggest using double-sided tape that can withstand at least 70°, like this one:…
When using double-stack mags with the Protean, I noticed that when using very worn (club) darts combined with them being left in the magazine for an extended period of time, you can run into an issue where, upon feeding the first round,…
I decided to buy a bond it super glue the thicker type. there are a lot of companies that use similar models. sometimes my model stands upright and sometimes lying down depending on which way my toolbox is. so i bought a rod of ptfe 16mm…
The SABOT Type-F is an alternative tip for the SABOT unjamming rod designed to better clear blocked flywheeler nerf blasters. Featuring the same flat, double-elastic chevron shape, with a narrower circular end, this fits in between more…
About This product is designed to prevent blinds from getting caught on window handles when being raised or lowered—suitable for the type of blinds and windows shown in the picture. Print setting Nozzle: 0.4mm Layer height: 0.2mm Wall: 3…
I decided to buy a bond it super glue the thicker type. there are a lot of companies that use similar models. sometimes my model stands upright and sometimes lying down depending on which way my toolbox is. so i bought a rod of ptfe 16mm…
The SABOT MOLLE Holster is a tactically mountable holder for the SABOT unjamming rod. Featuring an open container using the built-in tension of the elastic in the unjamming rod for retention, this holster is a perfect fit for 500mm of…
