Gashebel Ninebot G30/G30LD
Gashebel für E-Scooter Ninebot
- Downloads
- 704
- Likes
- 67
- Rating
- 5
30 models
Ersatzteil für einen Unterputz Spülkasten von Geberit, für welche Modelle das Teil passt weiß ich leider nicht. Ich habe mehrere Bilder und ein Paar Links angefügt damit Ihr es mit eurem Kasten vergleichen könnt. Das Teil wurde aus…
verstärkter Betätigungshebel
Gedruckt in PETG mit 3 Rändern und 0,15mm (oder geringere) Schichthöhe. Keine Stützen erforderlich. Neu! Modell mit Schriftzug wie beim Original hinzugefügt.
(English version below) Ersatzteil: Lüftungshebel Smart Roadster 452 (auch Coupé) Die Lüftungshebel des Smart Roadster Coupés können nach ein paar Jahren abbrechen. Tatsächlich sind die Lüftngshebel beim Hersteller noch als Ersatzteil zu…
Commonly listed as: Grohe 43519 DAL 330 As seen on TV!
Was tired of having these lying around in the cabinet and decided to draw this up. Each half is 225mm tall, glued together this is capable of holding up to 18 packs. Use the yellow #4-6 dry wall anchors to hang. I've found that staggering…
I did a poor job printing the original and wanted to have another go at it since my overhangs came out really bad (printing way too fast). With this reprint, I wanted to optimize the wall depth a bit and make it fit on my counter better.…
The Conjuring - Bathsheba - 2013 3D printable model.
This little dish will support the Sheba Perfect Portions cat food containers, so your cat can enjoy directly out of the container the food comes in, instead of dirtying a serving dish. The top heavy containers will slide around and fall…
DE: Passend für die Handbremse eines Deutz D 5006. Ich habe das Modell auf den Kopf gedruckt. Somit sind keine Supports notwendig. Zum Austauschen an der Handbremse Schraube oder Splint entfernen, alten Knopf raus, neuen rein und dann…
My cat likes to work on a single serving of wet food over the course of a day. Without a lid, it gets dried out. I designed this lid to keep the food fresh. Best printed in TPU, this provides a tight snap fit on a single serving tub.
Please write a comment when you have printed the model. I would be very happy. Dies ist eine 3D-druckbare Rekonstruktion des GROHE Betätigungshebels (Modellnummer 43550000), der häufig in Spülkästen eingesetzt wird. Nachdem mein…
I designed simple holder for Sheba Perfect Portions wet cat food. They don't stay put otherwise and I don't like emptying them into a bowl. Print with flat face on build plate. Just just about any material and normal print settings will…
I wanted a dispenser for Sheba 85-gram cat food tins, hence the design. It fits 8 tins and is under 200 mm high, so most printers can fit it. Print upright, with supports.
Updated with a taller version for better eating posture for the cat. Instead of putting food out of the tray and inside a bowl that needs to be washed afterwards, this object holds the tray itself with anti-slip feet so that the cat can…
Cat food holder/dispenser for Sheba or Iams split packs. Two sided for different flavors. The “bottom” alone holds 6 packs. I have not printed the “top” section. The complete tower holds 12 packs total, so a whole case.
Throttle lever for the Z30 gas controller by Meflex. It can be found on various vibratory plates, trench compactors, lawnmowers, etc. Total length: 94mm Total width: 39mm Height of toothed area: 29mm Diameter of toothed area: 32mm I used…
Ersatzhebel um den Rührarm entriegeln zu können.
This is an holder for sheba octogonal 85g portions. I printed mine with a 0.6 nozzle but it's possible to use other sizes.
Reparaturteil des originalen Auslösehebels für die Füllstandsanzeige des Auffangkorbes. Etwas verstärkt im Vergleich zum Originalteil. Empfohlenes Material: ABS oder PETG. (PETG hielt zuletzt ca. 3 Jahre bei häufigem Gebrauch des Mähers)
Dieser verbesserte Entriegelungshebel wurde speziell für die Kenwood Prospero KM286 entwickelt. Er ersetzt den defekten Hebel, der den Kopf der Küchenmaschine sichert und öffnet. Wenn der originale Hebel bricht, sorgt dieses Ersatzteil…
gedruckt auf Anycubic Kobra 3 0,16mm PETG schwarz Füllung 80%
Ersatz-Gashebel (Trigger) für eine RC-Auto-Fernbedienung. Das Originalteil war beschädigt und wurde in verstärkter Form neu konstruiert. Abmessungen siehe beigefügten Screenshot zur Kontrolle vor dem Druck. Modell besteht aus einem…
Complex Bathsheba Grossman Gyroid
Change filament at layer for multicolor print. I hope you like ❤👍 this model! Happy Printing!! 🎉🎉
Stützstrukturen: Ja
simple print should hold another 30 years now ;D
Geberit Betätigungshebel 240426001 Für Spühlkasten
Reparaturteil des originalen Auslösehebels für die Füllstandsanzeige des Auffangkorbes. Etwas verstärkt im Vergleich zum Originalteil. Empfohlenes Material: ABS oder PETG. (PETG hielt zuletzt ca. 3 Jahre bei häufigem Gebrauch des Mähers)