30 models
I had printed Luke Earl's airtag mount for my CUBE sadly it didn't fit my saddle, I simply used the .f3d file to replace the original 40 degree angle with a 28 degree angle. For more strength and a better resistance I printed it in ASA…
Print approx. €1.50–€1.83 excl. taxPreliminary estimate for one variant
Cable management bracket for under the table
A mostly hidden, compact way to store an Airtag on a bike. Designed for a mountain bike using a WTB Volt saddle, however this should fit other seats as well. Most seats have the same sized rails, with the only difference being the angle…
The tray (podstavec) gives your CW1 the same height as an SL1. Oh god! How this has always bothered my OCD! you can store mess in it. Spatulas, gloves, the funnel etc. you can either put the PSU inside or attach it onto the back side of…
I bought some IKEA TROTTEN Desks and some ALEX 36x70cm Drawer Elements thinking they would fit together, but it turns out there is about 2cm difference between the bottom steel element of the Desk and the top surface of the drawers. So i…
A remix of the Raspberry Pi 5 case, to support a Pimoroni NVMe hat mounted to the underside of the board.
I decided to create a Paper Towel Holder because the are a huge rolls that I like but no commercial holder that will fit this thick paper towel rolls Underneath. It will fit cylinders of paper of 180mm of diameter without problem. I use a…
If your LowRider 3 CNC takes the normal approach, with a vac hose from below hanging on hose hangers, this listing has nothing for you. If like me, your LowRider 3 CNC has a vac hose from above, and uses a drag chain, then you might find…
Designed a filament holder that hangs underneath my shelving for a snag free print Category: 3D Printer Accessories
Made this Holder for 20mm pvc pipe to fix to the wall. The added strap (for visuals mostly) is clipped in place after the install. Dont break it of its quite fragile. The spot below is for a 8mm cable or tube. I fitted this to get a gas…
Introduction This is an OpenSCAD script to generate slotted rails to hold steel print sheets underneath the Original Prusa Enclosure. The rails mount to the underside of the enclosure, using existing tapped holes in the base. The pattern…
These raised, replacement TV feet provide some extra clearance under your Philips TV. They lift your TV high enough to place a soundbar under the TV, instead of in front of it. It saves some space and makes your setup look clean and…
it has 3 holes for screws you can slide the hub in afterwards
I noticed that there was some wobble on the base plate of the Prusa enclosure when it was printing. I modified one of the stock feet so that it was slightly taller and so that a magnet could be installed. I then placed it under the plate,…
Its a raised version for runing cables underneath, ill make more sizes uppon request.
A remix of Ian’s Dune: Imperium Combat Marker with a more compact profile and reduced Z-axis height. I also added a “+20
Motor Holder With Rods Underneath
To fix a portable monitor of 12mm thickness underneath a bunk bed, I designed a holder that can be clipped onto the wooden boards holding the mattress. Required materials You need 4 printed clips 2 timber rods with a 12mm x 12mm square…
Upgrade your workspace with this Monitor Stand Riser With Storage Underneath, Keyboard Storage, Minimal Design Tested on 8+ FDM printers. Download and print immediately. **What's Included:** - STL File - 3MF File - OBJ File - Print Guide…
Printed in PETG so the board above can be wiped with water. Printer w/ 15% infill and a 0.4mm nozzle in 0.20mm SPEED settings.
This is a remix of maxwoodpecker's Anet A8 lcd table holder . I needed a lcd mount but for under my enclosure so I remixed his to do this, and have a slight angle to make it easier to view. Category: 3D Printer Accessories
I've created a remix of Sumi's model to make it better printable. I also removed the ridge on both edges because... time
This light mount was designed to place a front bicycle light below the rack. I've printed this at 0.2mm height, 3 walls, 15% infill and feels plenty sturdy. Designed so that it prints on its front face with minimal supports. it mounts…
Yet-Another Mac Mini M4 Stand with room for SSD with heatsink underneath. I've included my Fusion 360 design if you want to modify it. I started with a clean sketch not an imported mesh - so it is a very clean design. Lots of room for the…
Underneath mounting LP-16 socket case. Initialy designed for a M3x20 screws.
Four chess coasters, each with a real "White to play, mate in 2" problem. Solve it while your tea cools, then turn the coaster over: the full solution is engraved underneath. Printed in 4 colours, flush and perfectly flat so the cup never…
A deck board has to sit level on a zinc flashing that slopes . A solid shim does that, and creates the problem this one is built to avoid: it dams the runoff, so water stands permanently between the wood and the metal. That puddle matters…
This light mount was designed to place a front bicycle light below the rack. I've printed this at 0.2mm height, 3 walls, 15% infill and feels plenty sturdy. Designed so that it prints on its front face with minimal supports. it mounts…
