P
PrintablesCheruTijntje
IKEA VIMLE Wall spacer
Spacer to put the leg of IKEA VIMLE sofa in so it stays 10 cm off the wall.
Print approx. €4.34–€5.30 excl. taxPreliminary estimate for one variant
- Downloads
- 49
- Likes
- 15
- Rating
- 5
Search results: vimle
19 models
P
Printablesxarbit
IKEA VIMLE Couch Leg/Foot (for Robot Vacuum)
I printed this with PETG and made the walls thick but you can adjusted to however you need. The original leg height is 65mm, the one I created is 105mm, but you can use the Fusion360 file to adjust it to your likes. The original screw…
- Downloads
- 204
- Likes
- 30
- Rating
- 4.33
P
PrintablesThe occasional extrusionist
IKEA VIMLE fold-out sofabed cushion holder
Our IKEA VIMLE fold-out sofabed has removable seat cushions and back cushions. The area underneath the seat cushions is a very smooth consequently, the cushions "creep" forward whenever you sit down, stand up, or squirm around, leaving…
- Downloads
- 100
- Likes
- 7
- Rating
- 4
P
PrintablesSalakin
Couch Cup Holder Ikea Vimle
Couch Cup Holder designed for ikea Vimle
- Downloads
- 99
- Likes
- 14
- Rating
- 4
P
Printablesenergeticinterpretation44
VIMLE Cup & Remote holder Skadis
Cup & remote holder for the IKEA VIMLE sofa/couch (standard width armrest). Uses a printed Skadis board to allow for flexible attachment of holders. I deviated from the original Skadis hole geometry very slightly to make the overhangs…
- Downloads
- 79
- Likes
- 15
- Rating
- 0
P
PrintablesMacbambi
40mm higher Feet for Ikea Vimle Sofa Bed
If you raise your sofa, you will also need to adjust the fold-out bed. Here are risers for 40mm No support No brim
- Downloads
- 66
- Likes
- 8
- Rating
- 0
P
PrintablesTrap
Vimle Sofa foot extension
I needed an extension for the feet of my ikea vimle sofa so that my robot vacuum can fit under it. I specifically adjusted the height to fit the Roborock S55 (newer models should fit also. It's a simple print in place model which fits…
- Downloads
- 64
- Likes
- 6
- Rating
- 0
P
PrintablesBungo
IKEA VIMLE fold-out sofabed cushion holder shortened
Prevents the cushions from sliding/creeping forward.
- Downloads
- 50
- Likes
- 2
- Rating
- 3
P
PrintablesChristophe-P
IKEA VIMLE Méridienne Spacer Foot 35mm
pour rehausser le canapé de 35mm pour pouvoir passer l'aspirateur dessous et être mieux assis pour le numéro 1 il faut 6 pièces et pour le numéro 2 il faut 4 pièces imprimées en PETG avec 10 périmètres , 10 couches supérieures et…
- Downloads
- 32
- Likes
- 4
- Rating
- 0
P
PrintablesMacbambi
IKEA VIMLE foot riser 1/2/3/4/5/10/15/20/25/50 mm
Is your sofa wobbly or does it just need to be raised a little? Here is the solution. First print the test file and test if it fits to your model. Then select the desired height and print it out. Insert the riser into the original foot.…
- Downloads
- 31
- Likes
- 3
- Rating
- 0
P
Printablesrenzema
New Feet for Ikea Vimle Sofa Bed
I found that the feet that Ikea used with the Vimle Sofa bed were quite sharp and were tearing up my floor. I have created these feet. The Middle feet completely replace the feet that come on the sofa bed. The End feet go on top of the…
- Downloads
- 27
- Likes
- 3
- Rating
- 0
P
PrintablesMacbambi
IKEA Vimle Fire TV holder
Simple print. No support. I have adjusted the undersides of the holders accordingly. You can find a larger version here: https://www.printables.com/model/1107906-command-station-for-xtouch-for-ikea-vimle
- Downloads
- 22
- Likes
- 7
- Rating
- 0
P
PrintablesChristophe-P
IKEA VIMLE Méridienne Wall spacer
à imprimer en PLA ou PETG n'oubliez pas de poster vos photos de vos prints ça fait toujours plaisir !
- Downloads
- 20
- Likes
- 0
- Rating
- 0
P
Printablessrinathh
Parametric Tray for Sofa Armrests (IKEA Vimle)
This fully parametric sofa armrest tray is inspired by an award winning design from R&DStudio . I built this smaller version from the ground up in Fusion 360 to provide a hobbyist-friendly model that fits comfortably on the build plates…
- Downloads
- 15
- Likes
- 5
- Rating
- 0
P
PrintablesMacbambi
Command station for Xtouch for IKEA Vimle
Sorry, only for bigger printers. ;-) You can find the version for smaller printers here . The storage area is much larger and there is the possibility to store two TV remote controls. 242.5mm length - 198.46mm width - 67mm height The head…
- Downloads
- 11
- Likes
- 3
- Rating
- 0
P
PrintablesChristophe-P
Hue Play Sofa Ikea Vimle
pour fixer la lampe hue play a l'arrière du canapé il faut 2 vis de 3,5x12 mm à tête fraisée n'oubliez pas de poster vos photos de vos prints ça fait toujours plaisir Bon Print !
- Downloads
- 9
- Likes
- 2
- Rating
- 0
P
PrintablesCharlizzard
IKEA VIMLE Ventilation cover
Created a ventilation cover for IKEA's VIMLE footstool to close it up so small ( like LEGO parts ) items won't fall out the storage. Added a "connector" to join the parts if you need to split them to fit on your printbed. Just add it,…
- Downloads
- 6
- Likes
- 0
- Rating
- 0
P
Printables
IKEA VIMLE foot riser 1/2/3/4/5/10/15/20/25/50 mm
Is your sofa wobbly or does it just need to be raised a little? Here is the solution. First print the test file and test if it fits to your model. Then select the desired height and print it out. Insert the riser into the original foot.…
P
Printables
IKEA VIMLE Méridienne Wall spacer
à imprimer en PLA ou PETG n'oubliez pas de poster vos photos de vos prints ça fait toujours plaisir !