150 models
I wanted to hang my McLaren F1 horizontally, but I couldn't find a bracket for it. So I made one! Fusion 360 files included, feel free to modify. The screw holes might be a bit small, but I had no problem with 4mm screws. Gcode file is…
Print approx. €0.75–€0.92 excl. taxPreliminary estimate for one variant
Bosch Siemens Neff Coffee Maker Brewing Unit 11014117 part. When the brewing unit is blocked, this slider thing could fix it. Some pictures attached.
Print approx. €0.17–€0.21 excl. taxPreliminary estimate for one variant
Panel mount for XT60H-M connector. This variant was used on material that was ~ 0.625" / 15.875mm thick. Plug is a tight friction fit, installed from the back. The inner plate has just enough protruding to locate it in the hole and hold…
Print approx. €0.61–€0.75 excl. taxPreliminary estimate for one variant
A simple case to protect your spare Nitecore NL1416R battery when it's rattling around in the bottom of your bag while it's not in use. Cap comes on and off with a satisfying “pop!” Print with the open ends of the case and cap facing up.…
Print approx. €0.86–€1.06 excl. taxPreliminary estimate for PETGSource material: PET
Dyson DC25 upright vacuum wand cap, part number: 914114-01 modified from original design to fit the larger dc25 including cutout/alignment tab. Print tested at .8 nozzle with .4mm height. (.4 nozzle with .2mm provided as well). I like the…
Print approx. €0.57–€0.70 excl. taxPreliminary estimate for PETGSource material: PET
I recently purchased this bathroom vent with ceiling light open-box only to find out later that the diffuser lens was cracked. At this part of the story I think the average Joe would be stuck with a broken light fixture… but not this Joe!…
Print approx. €7.92–€9.68 excl. taxPreliminary estimate for PETGSource material: PET
Cover for mesh clip trunk OE: 7141855
Print approx. €0.61–€0.74 excl. taxPreliminary estimate for one variant
New for 4/24/24 - Minimal versions! Use the minimal versions to save time and filament if you don't intend to use a spacer. About The vertical mount supports nose-up or nose-down. The horizontal mount supports nose-left or nose-right. The…
This model is compatible with the lego system.
As seen on YouTube: Disclaimer: This is an acoustic model. As such, it does not scale, nor is it compatible with drivers other than the ones specified. Scaling / incorrect driver(s) will result in significantly diminished performance.
The original Worx cutting disc size is 145mm, with original blades the full cutting width is 175mm. There are other versions around but mostly for older Landroids. I wanted to create my own and also make some changes to the original…
Remix of https://www.thingiverse.com/thing:6060534 so it fits on an E53 X5
I was not happy with the wheel disc design on the Lego McLaren F1 Car released in 2022 (Kit 42141). Designed these as a replacement. The model you see printed in the pictures was done using a variable layer height of 0.2 at the base all…
Ive checked out plenty of other masks but ive always found two points to be not quite how i like them The mask often seems very big. The relative size of the forehead usually seems way too big in comparison to the ingame model. That might…
Created from the model uploaded on sketchfab by manilov.ap, cleaned up and made manifold in blender: https://sketchfab.com/3d-models/c141-6d71f3bd09ad48eb8145bba04caa3045 Printed vertically with tree supports from Cura, worked great at…
Skadis wall mount to fit the Mercedes F1 (42171) and the McLaren F1 (42141) Lego Models. Wall mount is printed in multiple parts to reduce the amount of supports needed, I would recommend tree supports for the main backing plate.
About the Yak-141 Freestyle The Yakovlev Yak-141 Freestyle, also known as the Yak-41, is a Soviet supersonic vertical takeoff/landing (VTOL) fighter aircraft designed by Yakovlev. Intended as a replacement for the subsonic Yak-38 with…
I tend to give a home to abandoned thinkpads with missing parts. I remixed my X200 HDD cover to fit a X230 I recently got. Printed without supports, 0.1mm layer. Fits like the original after a little bit of cleanup. Print Settings Printer…
I got a request from Neistsch to modifying my existing thing to fit the Worx Landgroid M500 series, so over a week or so of emailing measurements, images, test parts etc. we finally got the wheel fitted and adjusted to work. The images…
A fairly simple mask. Easy to print. Attach the Holders on all 3 sides. Glue or M2/M3 screws works. Feel free to choose what looks better for you. The elastic band is 2cm/20mm wide. Fasteners and back part are the same as my other mask.…
Remixed so there is no gluing involved. Print and push onto the axel rod.
Ein Ersatzteil für den Gewindetrieb eines Spiegelstellmotor des Opel Astra H (Corsa D). Für den Druck sollte ein SLA Drucker verwendet werden. Da die einzelnen Segmente das Gewindetriebs im Überlastfall überspringen können müssen, wurde…
I have a Trek Roscoe 7 that would not fit on the Zwift Hub smart trainer due to it having a Boost 141 QR rear. This adapter allows the Zwift Hub to properly connect to a Boost 141 QR bike. I printed the adapter out of Carbon Fiber Nylon…
This is a replacement insert for the Sidchrome tool sets shown. It will likely not fit other eras than those shown, as some of the individual tools changed dimensions frequently over the years. Found these files useful? Buy me a coffee !…
This model is compatible with the lego system.
I printed in ABS with bambu strong profile. I don't recommend printing it in PLA, since it can sag after some time. PETG might be ok! The wheels parts will fit very snuggly, but I still recommend that you glue them together. This support…
This model is compatible with the lego system.
This model is compatible with the lego system.
This custom 4-part adapter set allows you to use affordable Moskvich "LUXE" LX-2141-B filters with your Karcher WD3 vacuum! Designed for easy 3D printing and assembly, it eliminates the need for expensive OEM replacements. No supports…
This is a remix of Saunick's Twilight Imperium 4th Edition (TI4) war sun unit for FDM printing. https://www.thingiverse.com/thing:4191414 I found that the original model was too small for durable, usable fdm prints so I made an effort to…
This model is compatible with the lego system.
speacker cover Fiat Panda 141 with 10cm rise for speacker with tweeter
A pencil/pen vase with crisscrossing diamond shapes to keep your favorite pens and pencils in. It is 110mm tall and 83mm for the x and y axis. The photo shows the vase printed in regular mode with 2 walls and 3 bottom layers. The stl file…
Part Number 11141716134 Holder Part 11141716134 was found on the following vehicles: 3' E30 (01/1982 — 04/1993) 5' E28 (11/1980 — 01/1989) 5' E34 (06/1987 — 10/1990) Z1 Roadster (07/1988 — 06/1991) You can purchase an original one from…
Created because my drywall saw is pointy and scary. Tried @NT_1822008's model but it didn't fit my saw
Only requirement is to print it out of a material that is UV resistant. No supports needed, regular settings for any functional print. It's just very slightly oversized to make it friction-fit with the layer lines but doesnt really matter…
I have 1411 floppy disk drive without front panel. I have take second one and measured original. Logos are bigger at original because my printer is little inaccurate. Category: Computer
This is a sturdy Multiboard mounting bracket for a Ryobi single battery charger (model BCL14181H). The battery charger has mounting holes 105mm apart and the posts on this model, although small, are just about strong enough to hold it if…
This model is compatible with the lego system.
Hard to get this guard these days. Works as per the original. This one is printed in PLA as it's a prototype, but I'd recommend printing it in somthing more robust. When/if this breaks I'll print it again in Nylon/CF. Includes integrated…
*** Thanks for checking out this model! *** If you appreciate what I'm doing, consider buying me a coffee , and check out my other models for something else you might like! ********** In this version, the improvements are the same as the…
Network Switch Rack Ears for mounting a network switch into a 19" rack. Compatible with the HP1410-16G.
Frame sostitutivo per la cuffia della leva del cambio della Fiat Panda 141. Stampare in Petg o altri materiali resistenti al calore. Assolutamente sconsigliato stampare in PLA. 3D printable replacement frame for the Fiat Panda 141 gear…
Un montaje rápido, sencillo y fácil para el monoplaza de Fórmula 1 Technic McLaren de lego 42141 en posición horizontal. Se utilizan tres tornillos para paneles de yeso para colgarlo en la pared. Configuración de impresión 3D Altura de…
Costco item number #1410571 IRIS 12.9 buckle up tub Wife wanted to replace the cardboard dividers she was using with something a little more durable. PLA adjust infill/walls as you see fit
Two STL one logo and one NO logo. For logo to come out recommended a smaller nozzle and/or quality print settings. Remix of Part Number 11141716134 To make it stronger and thinner in the engine bay. Less slop in the cable moving around.…
Hundreds of thousands of Johnson Controls (JCI) Metasys VMA-1410 and VMA-1420 Variable Air Volume (VAV) controllers exist across the world. Hardware wise these controllers are very reliable however the common point of failure after about…
This Prints in 0,3Layer Size is for 32mm RPG the Battle info is in Wikipedia https://de.wikipedia.org/wiki/Schlacht_bei_Tannenberg_(1410)
I created this remix so that I could have a place to attach my transducer arm without taking up an entire mount location on an inflatable skiff. I happened to have a Scotty 141 transducer mount so I remixed the linked model to use the…
Fits a little tight. might be able to print at 99% for an easier fit. I just hit it on with a hammer and it fit fine.
Printed in PETG, Split the STL into the two parts/objects. Orient the Clip to reduce breakage risk if using FDM printing
Bosch MUM9 clutch - 10004141
On a big truck this would be the hydraulic cylinder which lifts the bed/cargo. This part was missing, I could not find a fitting one.
Stabiles Scharnier mit Inbusschraube B5x50 als AchseStabiles Scharnier mit Inbusschraube B5x50 als Achse PLA oder PETG 100% Infill
6/29/2024 added model modification Print Prusa Filament PETG 0.15mm structural, MK3.5 for the top layer, ironing can be used and then sanded with fine sandpaper. printed without padding mirror printed text freely editable in Prusa slicer…
Cookie stamp Pi 3,14159265358979323846
Part One of the iconic “Days of Future Past” storylines in X-Men comics started right here! The cover of Uncanny X-Men #141 was instantly iconic and has been often imitated. The Frame is not included, but is OtherDogDesigns customizable…
Wall mounted hanger for LEGO formula model
La Crosse thermo humidity tx141th sensor shield cover. I printed the main body upside down with no supports on my Bambu Lab X1 Carbon printer.
Рамка кулисы кпп москвич 2141
Scale to 25mm width, print on the side with tree supports 22.12.2025 - fixed thin wall
Print at home Dust baffle / block for the dust collection area on Laguna 14|12 and 14|BX band saws. I cut mine in half when the blade snapped, so 3d printing to the rescue!
10" Rack Ears for an HP 1410 16 Port switch. This switch is 1U deep and 208mm wide to check for compatibility with other HP models Printed with large side on the bed with 3 walls from PETG
This is my first attempt so hope it works out OK :) Supports are probably optional. Printing in PETG will work without supports for the overhangs. Modeled in Fusion 360 (source file included) so please feel free to improve!
This is a mounting bracket for the Protectli V1410 gateway. I drew this to use M3x12mm socket cap screws with a washer.
designed to replace: Thetford winter cover 69109980 for the N3241 N3142 Slim tower fridge. with a 432x257mm vent. model made out of 3 parts to fit my printer. printed in PETG. didn't have time to test fit the middle part yet, but should…
Adaptateur fixation chargeur Ryobi BCL14181H permettant de le fixer dans l'autre sens avec le cable en sortie basse et les voyants vers le haut Fixation avec 2 Vis M4*10 Je me suis basé sur le fichier Ryobi RC18120 Charger Holder de…
Replaces the original 3 blade plate. For cleaner cuts and less noise. Pause print after ~7mm and insert standard M5 nuts
una volta stampato il portabicchieri, utilizzare i pin di centraggio e colla bicomponente per incollare il tutto. da stampare preferibilmente con PETG/ASA/ABS. sconsiglio il PLA Seguitemi sulla pagina ig:…
Втулка рычага сцепления москвич 2141
A dial indicator holder for Proxxon MF70 that screws onto the spindle shaft and uses a Noga FA1410 holder (part of Noga PH2040) to mount the indicator It shouldn't be too complex to manufacture the compliant dial holder part itself…
Втулка педального узла москвич 2141
This is an easy print and you can make it two toned by paysing on Layer 6 to swap colors. Makes a great gift for the book and math lover in your life.
Being tested at this moment. Might need slight Z-adjustment. Print as is, it might (or might not depending on printer) need few supports on overhangs.
Got a cheap secondhand fridge for drinks, an Dometic RH-141DG that was used in a hotel. Very nice silent fridge. But it came missing one of the pin bushing, which meant the door was wobbly and weird. Designed an replacement, based on…
Hollow Clock Version 3.14159 Please note that this is a moderately complex build. If you don't have experience with3d printing, wiring electronics, or loading code to a Pi Pico, you should try a few simpler projects first. This is a remix…
ORGANIZZATORE GT141 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante: Artillery Sidewinder X2
Для салонного фильтра Daewoo Nexia. Категория: Транспортные средства
A minimalist WC door hanger , inspired by the iconic single-line aesthetic of the 1970s cartoon La Linea . Its clean, playful silhouette and clear toilet symbol make it an excellent fit for homes, hotels, offices, gyms, and wellness…
This is a replacement for a broken part, belonging to the lever of the folding roof from a Fiat Panda Type 141. Dies ist ein Ersatz für das kleine Verbindungsteil am Verschlußhebel für das Faltdach eines Fiat Panda Typ 141. Printed in…
I wanted something to keep my work area tidy, but have a little fun too. My day job is as a rail engineer. So I modeled an organizer in the shape of 141lb rail to keep everything I use on a regular basis close at hand. The blue stripe…
Temperature Controller multi-function switch housing. Made for the 220VAC version which is thicker than the 12VDC version due to the added transformer. this housing should work for both versions. NEW VERSION with triangle cooling vents is…
Is it reffined? No. Does it work to replace 53141-958-000? Yes. Enjoy.
A simple cradle for storing a .250” travel Starrett 24-141 dial indicator. May fit some other indicators but designed for this model in particular. I intend to upload models for all of my various plunge dial and test dial indicators.…
Door Panel Fastening Clip for Alfa Romeo, Fiat, Lancia — 14188282 Model compatibility information for OEM part number Alfa Romeo, Fiat, Lancia: 14188282, 46306526, 92511089 Marca Modello Anno Piattaforma Tipo Motore Notes Alfa Romeo 75…
Printed on a K1 Max with no support required.
Втулка подголовника москвич 2141
ENG: As the title says, free 3d models for the swaybar bushings for the Lancia Y10, also the Panda 141, since the swaybar can be mounted on it. Use TPU 95A ITA: Come dice il titolo, modelli 3D gratuiti per le boccole della barra…
Recreation of the spark plug wire holder. Probably fits other cars that use the 999 FIRE engine. Works well printed in Nylon by JLC3D. Simplified the attachment clip and replaced it with a friction fit.
I designed this simple mounting solution for mounting my grphics tablet to my desk out of the way! It's designed for the Aiptek Media Tablet 14000U (model WMK-H141). Apparently I was too cheap to buy a Wacom! Dimensions… Desk beam…
Needs at least 300 x 300 build plate. Printed Case in PETG and insert in LW PLA
This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/j6Y03d6NMtU Category: 3D Printing
Поперечина крепления панели 2141
This spacer keeps your Mojave Grom battery from sliding around. A piece from Arrma part number ARA-1418. Fits Mojave Grom 3S. Print with flex filament for max shock absorption. To reduce weight and improve shock absorption, print with 2…
This simple piece slides/snaps on over the exposed leads of the Castle Creations 1412 sensored brushless motor. It likely works on many other models with a 36mm diameter body. I printed mine in PETG and oriented it as shown without…
![Twilight Imperium War Sun Unit for FDM [thing:4191414 remix]](https://media.printables.com/media/prints/324342/images/2796301_47c38599-b315-4cbc-af3d-71be66029c34/pxl_20221124_212122224portrait.jpg)
![Mitsubishi / Proton roof clip MB814153 [testing]](https://media.printables.com/media/prints/59b23e21-a081-4f85-9f4f-d0ffef553a20/images/10892017_a0413855-da53-419b-9981-607a1950fb67_b86feaf8-7d12-433f-a974-c01be487d3ff/2025-10-14_17-40-02.jpg)
