Counting matching models…
The Jobo 1500 series tank system does not officially support processing 4x5 sheet film. This insert fits 2 sheets and requires atleast 3 35mm film spools of vertical space. So you need the 1530 tank module to fit it. It prints in two part…
Print approx. €0.12–€0.15 excl. taxPreliminary estimate for PETGSource material: PET
Developing 8 sheets of 4x5 film at a time. Print with PETCF for best performance. PLA is too crunchy PLA+/PETG/ABS are too soft ABS-CF should also work. Category: Camera
Since they are constantly getting lost and the children are sad, I have constructed two replacement arrows. They are compatible with the Lego Projectile Launcher (part number 15301) and fit into the rear handle end of a "Simba - Next…
This model is compatible with the lego system.
End caps for 80/20 Inc's 1530 (1.5" x 3.0") t-slot extrusion. Push fit into place when printed with ABS. Three options: with holes for 1/4" flat head screws, solid, and with holes for routing cable in t-slot. Print Settings Rafts: Doesn't…
This model is compatible with the lego system.
From the official website: 1530 is a 1.50” x 3.00” fractional 15 series rectangular T-slot profile with six open T-slots, two on each 3.00” face and one on each 1.50” face. The profile has align-a-grooves to assist in alignment when…
Simple end caps for 15 Series t-slot extrusion for 1515 and 1530 profiles. Easy to pop in either threaded or unthreaded ends. The pegs do break when you remove them as expected, but they're tight so they dont rattle from vibration on a…
Replacement Hooks for the Playmobil pirates (71530) Ships Sails. The Non-foldable is for the Top Part of the Sail. The Foldable is for the Bottom Part of the Sail. The Foldable one is a bit finnicky, but once in place, it should work…
I've included two versions. One with stubs to lock Figures in place and one without. I also included a test to check if your printer settings will allow the platform to fit. To mount it on your ship, just slide it in. you may need to use…
ochranný kryt výstupu převodovky pro LT 1. generace
This cap is designed to prevent the sails of the Playmobil pirate ship from popping off the beam. I printed it 25% larger since it didn’t fit well with my printer. If the sail beam fits into the hole, it should work as expected. If you…
The Cooper Bussmann 15302 Series, including 15302-2-2-4, is now OBSOLETE . Replace with Eaton 15305-2-2-4. Available at Mouser (not sponsored).
Ego 56V AH1530 bumper head, this is NOT the entire bump head, only the part that spins on the bearing and contacts the ground. Update (1/31/2023): Found that the small plastic shaft was weak, so added a 3mm diameter screw and nut to…
This is a simple design meant to be a tight-fitting channel cover for 1530 extruded aluminum bars. I designed this so I could hide wires to my lights and cameras on my Xtrusion Overland bed rack in the channels themselves, instead of…
My own design for an AuthentiKit "Wedge" part that is designed to attach to 1530 (8020) aluminum extrusion instead of the default AuthentiKit mounting arm. Fits into the standard "Dovetail" part. Original AuthentiKit files available here:…
A sturdy mount for small to medium sized PTZ cameras attaching to a vertical section of 1530 extrusion. Designed to allow for some adjustability on the camera position horizontally for clearance. I use it with a ball head mount because my…
After a while the high efficient floor nozzles (also called free-flow) floor nozzles of the Numatic Henry (HRV-160, HRV-170 and so on) fall off. The wheel itself is pretty fine, but there is a little shim inside which wears down easily. I…
