P
Printablesthall72
Lego Compatible (11605.dat) Figure Friends Hair Long with Ponytail French Braided with 1 Pin Holes
This model is compatible with the lego system.
- Downloads
- 181
- Likes
- 29
- Rating
- 1
Search results: 1605
Counting matching models…
P
PrintablesPaul
Improved Adaptec 71605 Fan Mount
See original model for addtional info: https://www.printables.com/de/model/713752-adaptec-71605-fan-mount
- Downloads
- 68
- Likes
- 7
- Rating
- 0
P
PrintablesJohn Carroll
Adaptec 71605 Fan Mount
While setting up a new fileserver, I needed a new Host Bus Adapter (HBA) card to connect a bunch of hard drives to. The Adaptec 71605 can be found used for cheap and it is a great alternative to an LSI card. The Adaptec 71605 runs HOT…
- Downloads
- 62
- Likes
- 8
- Rating
- 0
P
PrintablesBRS-ENGINEERING
Z-Upgrade II v2.07b (SFU1605)
SFU1605 Version - Extend the Z distance of 50mm (need 50mm longer ballscrews spindles), available for 0-2-3-4mm underplates otherwise through height modualator. Corner completly reinforced and high ability, keep the frame aligned from the…
- Downloads
- 48
- Likes
- 8
- Rating
- 0
P
Printablesgsd
Steam half machine / GB-BSRE-1605
Size of box +- original steam machine, but is height is half. Original sizes view in internet. Installed SteamOS 3.8 convert this device to steamdeck hardware equivalent. Front panel is canonical from original steam machine with magnet's.…
- Downloads
- 35
- Likes
- 12
- Rating
- 0
P
Printablesjuh
RCWL-1005 and RCWL-1605 sonar distance sensors for fischertechnik
Compared with the ubiquitous HC-SR04 sensors, these modules come with a combined emitter/receiver and an optional UART or I2C-interface. Unfortunately, their minimal range, 25 cm, is much larger. More info on these sensors and an Arduino…
- Downloads
- 32
- Likes
- 3
- Rating
- 0
P
PrintablesBRS-ENGINEERING
Z-Upgrade 2.8c Definitive Edition 1605 (BRS-Oldham)
LAST AND DEFINITIVE REVISION of my high precision Z system with anti-wobble with SFU1605 I focused to reduce parts quantity, BOM, and make it way more easy to implement; -Easy installation over a Stock 3.1: Same Vcore 3.1 bottom plates…
- Downloads
- 30
- Likes
- 2
- Rating
- 0
P
PrintablesSmith
Adaptec 71605 Fan Mount - No Heat Set Inserts
Required Hardware: 4x M3x8mm screws - for the fan 2x M3x12mm screws - thread into the standoffs
- Downloads
- 26
- Likes
- 1
- Rating
- 0
P
PrintablesMaSa_0815
Re-Insert assistance tool for SFU1605 nut
I accidentally lost a tiny ball while removing the nut from an SFU1605 ball screw — one got stuck between my tool and the thread and jumped out. While searching for a way to reinsert it (and reading a few horror stories), I came up with…
- Downloads
- 19
- Likes
- 1
- Rating
- 0
P
PrintablesLeoRc
SG1605 Pro - body support
I've changed wheels to a bigger radius so my small brushless beast needed the body to be lifted a little. result https://bit.ly/LeoRc I used PetG first and it worked well until it crashed. The rear are still good, but I reprinted the…
- Downloads
- 16
- Likes
- 1
- Rating
- 0
P
Printablescombobulator
Lens Cover for Bosch GTC 400 C Thermal Camera (16055002CR)
Lost the lens cover for my Bosch thermal camera so I decided to recreate it based on photos and share it here in case anybody else needs it. It fits perfectly and follows the original design as closely as it can. There is, however, an…
- Downloads
- 10
- Likes
- 1
- Rating
- 0
P
Printables3Dd
protection moteur Jeno 3.5 pour moteur 1605.5 T-hobby
protection moteur Jeno 3.5 pour moteur 1605.5 T-hobby , a imprimer en TPU 95a . Attention j ai crée pour 2 épaisseurs pour bras épaisseur 4mm et 3.5mm Le model 1604.5 grip (photo avec la ligne bleue ) est avec une attache pour les fixer…
- Downloads
- 2
- Likes
- 0
- Rating
- 0
P
Printables
Z-Upgrade 3.2c/d for VCORE 4.0 SFU1605-SFU1204
Adaptation of the production grade "Z-Upgrade" for VCORE 4.0 Upgrade to replace the original Z with a ballscrew system. More precise, very reliable over time, offers a very high repeatability in the Z movement compared to a trapezoidal…
P
Printables
Z-Upgrade 3.2d-H for tall VCORE 4.0 SFU1605
This is a Z-Upgrade 3.2d-H iteration (H, for heavy), It answers the need to make a very tall printer (800-1500mm) It features a new Starlock unit, with M5 square nuts to withstand the load The bottom plate of the VC4 need some…
P
Printables
Ball screw SFU1605 tool to remove the screw
I designed this tool to remove the nut from an SFU1605 (or any other 16 mm ball screw). I needed to cut the flange for my SFX80 simulator to fit the slider of the 8080 aluminum profile. The screw was in the way during grinding, and I…