Counting matching models…
Trash bag dispenser Can hold a roll of 35L bags or any roll of bags with 6cm diameter and 15cm height/length 2 screw holes Easier to print bottom chamfer than on the original model Remixed from Augustas Kazlauskas fine Trash bag holder to…
A direct drive extruder for the UM2 using a PG35L Nema 17 geared motor. It's light, it's super quiet, and best of all... it prints Ninjaflex! With a 1.75 filament setup, flexible filament would not print on my bowden-based extruders... so…
I recently installed an IKEA HÅLLBAR pull-out frame in my kitchen but wanted to use it with the larger 35L bin . The 35L bin is narrower than the smaller ones which means it slides around in the frame a lot. These inserts clip into place…
This is a stackable grid inlay for the Tightvac 2.35l box. Printed with 4 walls, 25% gyroid infill, 0.16mm. Fusion files for 55mm and 33mm attached. Have fun for remixing.
I needed to fit two bin bags for recycling. You should be able to fit two of these inside the bin. I ended up using only one to fit one bin bag for plastics and for paper I just throw it directly in the bin as it's usually not dirty (see…
Da mir die Originalachse abgebrochen ist, habe ich einen Ersatz modelliert. Unbedingt in PETG mit Support drucken, 100% Infill ist wohl ein MUSS.
This a two part support for the trash can “Müllex single 35L” made when i saw that i only bought the thrash can itself without any of those necessary pieces. It consits of 2 pieces one for the door use to link the door and the trash can…
Modification of Desiccant Container - Paper Storage Bag - Triangle tolarger dimensions from a request. Original design here: https://www.printables.com/model/38730-desiccant-container-paper-storage-bag-triangle Want to modify a design and…
Cornerbracket for D-link surveillance camera DCS-8635LH and a "lid" for the lower part of the camera.
Bass reflex with minimal aeroport at the end. Designed for a 35L enclosure and a 10-inch speaker. Aeroport width: 80cm External width: 79cm Internal width: 77cm Total length: 162cm
Ein Rollenhalter für Abfallbeutel 30L 0der 50L mit Schneidezähnen zum abreisen und aufklipsprofil für 19mm Spanplatte auf einen Fachboden zb.
This allows the remote mounting of the Brewzilla Gen 3 - 3.1.1 control panel. It's designed to hook onto the existing Brewzilla handles and the feet then allow the angle to be adjusted. It includes the housing plus parts to mount it with…
Gemini 335L mount for my AMR Additional parts : M3 screw x 2 M4 screw x 2
Here is a 2 bin holder for IKEA 18inch drawers so the garbage does not fall and move everywhere
The 35L Hills foldable basket (22cm x 45cm x 35cm) stands up using bamboo corner inserts that slide into a fabric sleeve, attached with velcro at one end allowing the basket to fold flat. One of my bamboo inserts snapped in half, and…
Designed to be printed without supports. PLA is fine but you can use any filament with this model. There are Shelf Mount Rails and Wall Mount Rails for your convenience. Requires: 2x M3 Bolts of any length 2x M3 Hex Nuts NOTE: Your hex…
This insert basket is designed for the Mestic MCC-35 and MCC-25 compressor fridge. The basket follows the tapered shape of the fridge’s inner walls. Approximate Dimensions Bottom: 325 × 246 mm Top: 331 × 253 mm Total height including the…
Modification of Desiccant Container - Paper Storage Bag - Triangle tolarger dimensions from a request. Original design here: https://www.printables.com/model/38730-desiccant-container-paper-storage-bag-triangle Want to modify a design and…
Here is a 2 bin holder for IKEA 18inch drawers so the garbage does not fall and move everywhere
Bass reflex with minimal aeroport at the end. Designed for a 35L enclosure and a 10-inch speaker. Aeroport width: 80cm External width: 79cm Internal width: 77cm Total length: 162cm
I needed an exhaust port for my enclosure, which has wooden side panels. I wanted to repurpose an old, dead PSU fan (NR135L); however, there were no existing STL files for its shape. So, I custom-made one, using other models from…
I used m3 equivalent wood screews, easy slide on and of. USE BAGS!!! or it will rot inbetween the layers.
Support: Yes Infill: 10% For instalation use only 2 screws 4x16.
