Counting matching models…
Layer height: 0.2mm Nozzle temp: 200°C Bed temp: 60°C Print speed: 50–60 mm/s Infill: 15–20% (grid or gyroid) Wall count: 2–3 walls Top/Bottom layers: 4–5 Cooling fan: 100% after first few layers Supports: No Adhesion: Skirt or brim if…
Ender3V3KE CR ADXL quick mount without extra screws, just using the 6 screws that coming with the sensor.
Just a simple mount for the Creality Nebula camera. It use the original position and screws of the Nebula Pad. Best to use it with a standalone Pad stand - > see my models ;-) *printed my screw with Hyper PLA (carefully tighten the screw…
Clip to move out filament run out sensor out of middle of the top rail in ender 3 v3 KE. In my case I have filament holder put at left side of my enclosure so I had to move the filament sensor to the left as well. There are two models -…
I have dual 5015s on my KE and the standard model would not fit. I didn't want to remove the fans as it would skew the results with the variation in weight. It's not great for the placement as I know it should be as close to the nozzle as…
It goes on pretty snug right bellow the pressure sensor, maybe you might need to sand it down a bit for a perfect fit but it's better this way so it goes on as snugly as possible reducing vibrations as much as possible. There's a 3D…
Description: Allows turning 90 degrees the spool's orientation in Ender 3 V3 KE/SE 3D printers. Its a simply desing that also allows to mantain the filament sensor in the original position. Doenst need supports. Additional materials: 1 M5…
Clip for led: https://www.aliexpress.com/item/1005006322232967.html
3 Color Colorizer Clipon Attachment for Ender 3 V3Ke. Prints with no sopports. Printed with PETG .2, 3 Walls , 2 Top & Bottom, !5% Grid infill. Would advise printing with a raft Helps support bottom tube. Works Very Well.
I had a problem with crochet on original model, it was weak. So, after I printed spine cable chain I realise that top part of chain shoud be connected to nebula support, so here we go) but still need to use plastic clamp for stable at…
It's pretty self explainatory really, needs supports.
This is a 3D printable replacement or upgrade part specifically designed for the Creality Ender 3V3KE 3D printer. It functions as a Y-axis tensioner cover or end cap, replacing the stock black plastic component. Features: Compatibility:…
This camera mount can be used on the right or left side of the Ender3V3KE. It mounts to the V Wheel cover and uses the factory screws. There is also a plain cover if you want to add a little color to your printer or if you want the sides…
Berg torch mount for Ender 3 V3KE
Ender3 V3 KE 우측 상단에 설치하여 아래 또는 뒤쪽에서 오는 필라멘트를 볼 가이드로 잡아주는 역활을 합니다. It is installed in the upper right corner of the Ender3 V3 KE and serves as a ball guide for filaments coming from below or behind.
Simple blocks that goes under the hotbed to support it while transporting the printer. Its a snug fit and wont allow the bed to squish down bending the steel rods to bend. HEX pattern for weight reduction and cool points. I printed them…
Layer height: 0.2mm Nozzle temp: 200°C Bed temp: 60°C Print speed: 50–60 mm/s Infill: 15–20% (grid or gyroid) Wall count: 2–3 walls Top/Bottom layers: 4–5 Cooling fan: 100% after first few layers Supports: No Adhesion: Skirt or brim if…
Simple blocks that goes under the hotbed to support it while transporting the printer. Its a snug fit and wont allow the bed to squish down bending the steel rods to bend. HEX pattern for weight reduction and cool points. I printed them…
