Counting matching models…
The model has been cut into several section to be able to print it without support. It has been increased in size to a length of 250mm. To make the lineup for the gluing easier FilaPins are added to each cut. For that you will need 6…
This model is compatible with the lego system.
This is the Model Town House set. Like this and check my other sets if you want me to share more. The instructions are at the bottom of the files, and the specific colors you need to print with are in parentheses in the folder's name, but…
This is an additional version of Part 3 and 4 of the NCC-74959 Voyager. Displaying the model in warp flight with lifted warp nacelles. You will need Part 1 and 2 from this version:…
The studs for the muffler heat shield on P2 series Volvos (V70II, S60I, S80) corrode due to the influence of moisture, the contact between aluminium and steel, temperature and of course age. The result is that the original plastic nut…
I made a simple hanger for the Festool 495717 FS-PA parallel attachment guide rails. I could not find a model for this attachment, so I quickly put something together that suits my needs. If it is of some benefit to your workshop, I would…
This model is compatible with the lego system.
A simple, printable stand for Thinkpad T490 or T495 laptops. Vertical and horizontal orientations are supported. Just print two copies, and you are good to go!
This model is compatible with the lego system.
This model is compatible with the lego system.
Eine Halterung für das Garmin nüvi 2495LM und baugleiche Geräte. Ich habe die Halterung gebaut, um das Gerät auf einem Boot zu verwenden. Sie kann mit einer Schraube zentral werden und in 2 Achsen gedreht werden. Es werden noch 2 Schauben…
Boost your Playmobil farm equipment! This side-mounted mower (sickle bar mower) clips onto the Farmer with Harvesting Tractor (70495), allowing your farmer figure to cut again grass or crops with added detail and play value.
Did not want to buy complete hose set OEM 5230495 for 140 euro so took it into my own hands and made a quick adapter and took a normal 10mm festo pneumatic hose and pressed on. You need to remove all the hose from the one-way valve since…
Closing Cap for Kverneland Accord CX Discs Coulters (ref. AC495730) There are two different versions. The outside diameter is equal, but the inner diameter ist different (22 mm or 29 mm). Print instructions Supports: No Resolution: 0.2mm…
I made a model for the rod end of the shock absorber, because the part was not available at the time. Its a quick fix, but obviously not as good as the real part. The real part can be found under the number ARA-1495
So, getting replacement parts cost $35+ so I wanted to make a replacement model. Hopefully this helps you guys!
Rounded off some of the edges to make the model more safe.
I exchanged the armrests on my IKEA Markus office chair for the adjustable Safco 3495BL Metro Adjustable Arm Kit . They were slightly too low, this adapter raises the pads 4cms, so the armrests reach 11.5 inches from the bottom of the…
Repair part - a latch for Decathlon 8595495 - Hard case Smartphone Mount. Place the model either on the left or right side for more durability.
Aretace dveří pro karavan Hobby Exclusive 495 - pravděpodobně kompatibilní s dalšími modely Hobby.
Microphone stand for pipe (diameter 28 mm) – Brüel & Kjær Array Microphone Type 4957. The height of the microphone is 5 cm above the bottom edge of the model.
Standard settings are just fine
This is a simple model that allows you to hang your Skil 4495 jigsaw on the wall or any other vertical surface. This model includes the FreeCad source file, so it's easy to adapt it to most other jigsaws.
"Northwestern ME495: Intro to AM 2026"
A remix of the RAK19003 case originally designed by N7TRX , adapted to fit a 3000mAh LiPo battery (size 974958) . Notes: Ultra-compact: Space inside is tight, so take care when routing your cables. Snap-fit: At 100% scale, the shell snaps…
ORGANIZER GT495 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante 3D: Anycubic Kobra S1 Combo Laser: Mecpow X3Pro 10W
This model is compatible with the lego system.
Before you go further! This model is available for free for all my supporters in Printables Club 🧡 Consider joining my club to have access to all ⭐⭐⭐ exclusive projects ⭐⭐⭐ and be part of my community! This project is for personal use…
This model is compatible with the lego system.
ORGANIZER GT495 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante 3D: Anycubic Kobra S1 Combo Laser: Mecpow X3Pro 10W
This model is compatible with the lego system.
